Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Rear mounting brackets for Grass undermount slides give a dedicated way to support Grass Dynamic NT, Grass Elite, Grass Dynapro, and Grass Maxcess undermount drawer slides at the back of the cabinet, which helps keep the slides aligned and operating smoothly over time. This Grass America universal rear mount bracket is described as a rear socket for Grass undermounts, so it is designed as the interface between the slide and the cabinet rear wall, turning a flat cabinet back into a secure mounting point for the slide. The non-handed design means the same bracket can be used on either the left or right side, which simplifies setup at the bench and reduces the chance of mixing parts during installation.
This rear mount bracket is identified for face frame application, so it is intended to support undermount slides in cabinets where the slide front attaches to the face frame and the rear needs a bracket to reach the cabinet back. By defining the drawer range as 12 inch to 21 inch, the part scopes its usable installations to common drawer depths, which helps align slide length selection with rear support planning. The mention of pre-drilling 2.5 mm, or 3/32 inch, gives a concrete pilot drill size, which supports a consistent screw fit and helps maintain holding power in typical cabinet materials. By combining non-handed use with these defined application details, the bracket supports a straightforward undermount layout process on face frame jobs.
This Grass America universal rear mount bracket is identified as a rear mounting bracket, non-handed for Grass Dynamic NT, Grass Elite, Grass Dynapro, and Grass Maxcess undermount slides, so it functions at the back of the cabinet wherever these Grass undermount slide systems are used. Because it is for 12 inch to 21 inch drawers, it aligns with many standard kitchen, bath, and utility cabinet drawer depths that fall within this range, anchoring the rear of the slide in those installations. The bracket is also described for face frame application, so it is applied in face frame cabinet construction where the front of the slide references the frame and this bracket provides the rear connection, tying the slide to the cabinet case and supporting consistent drawer travel.
The Grass Dynamic NT rear mount bracket, also referred to as a rear socket for Grass undermounts with manufacturer part number 7950.VE300, provides a dedicated connection point between the specified Grass undermount slides and the cabinet rear wall, which supports alignment of the undermount system from front to back. The non-handed design means each bracket can be used on either side of the drawer, simplifying layout because the installer does not need separate left and right parts when setting spacing or adjusting for case squareness. By stating a drawer length range of 12 inch to 21 inch, the bracket focuses its use on common slide lengths, which helps the installer pair slide sets and rear brackets logically across a run of cabinets. The recommendation for pre-drilling 2.5 mm, or 3/32 inch, gives a specific pilot size that helps control screw engagement into typical cabinet materials, supporting repeatable installation torque and reducing the risk of material damage around the rear mount area.
This Grass America rear mounting bracket is specified for Grass Dynamic NT, Grass Elite, Grass Dynapro, and Grass Maxcess undermount slides, so it supports those slide families at the cabinet rear.
This rear mounting bracket is described as non-handed, so one part works on either the left or right side, simplifying layout and part management during installation.
This rear mount bracket is identified for 12 inch to 21 inch drawers, so it is suited to undermount installations using drawer lengths within that range.
This rear mounting bracket is specified for face frame application, so it is used where slides reference a face frame and need a rear support to reach the cabinet back.
This product description recommends pre-drilling of 2.5 mm, or 3/32 inch, providing a pilot size reference to guide screw installation into cabinet material.
The manufacturer part number for this Grass rear socket is 7950.VE300, which helps match it precisely to specified Grass undermount slide systems.
This Grass America universal rear mounting bracket, identified as manufacturer part number 7950.VE300, is described as a rear socket for Grass undermounts, which directly aligns it with Grass Dynamic NT, Grass Elite, Grass Dynapro, and Grass Maxcess slide systems. With its non-handed design, drawer length range of 12 inch to 21 inch, and face frame application focus, it is positioned for use in many standard cabinet drawer layouts using these undermount slides. For projects built around these Grass undermount families, this rear mount bracket offers a defined way to support the slides at the cabinet rear and maintain alignment from frame to back.
Sold In: 1 Each
