Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
PowerSync wired controller gives you a single door sensor that switches Tresco 12/24VDC single color dimmable low voltage lights on when the door opens and off when it closes, so lighting follows cabinet or door movement without extra steps. The controller is compatible with both 12VDC and 24VDC systems, allowing one part to serve across typical Tresco low voltage runs in a shop or installation. The smaller sensor design uses an 8mm diameter hole for recess mounting, which lets the sensor sit discreetly in a drilled bore while keeping the face clear. A nickel finish on the sensor presents a neutral metal look that blends cleanly with many hinge and door hardware setups. The door open, light on; door closed, light off logic creates a predictable response that supports consistent user experience across multiple doors on a project.
The single door sensor works as a wired controller in a Tresco low voltage line, so input and output wiring pass through the sensor to control the lights when the door position changes. The controller operates on 12VDC and 24VDC systems, so it fits typical Tresco LED layouts without needing different voltage-specific sensor models. The smaller sensor body and 8mm recess hole give a clear drilling dimension, which supports accurate boring using standard bits during cabinet construction or retrofit work. Nickel finish on the sensor provides a finished appearance when recess-mounted near hinges or edges that remain visible during door operation. The door open, light on; door closed, light off behavior uses the door as the switch, so users do not rely on separate wall or inline switches at each cabinet.
This single door sensor works with Tresco 12/24VDC single color dimmable low voltage lights, so it fits installations where those lights are already part of the layout, such as cabinet interiors or similar low voltage zones. The controller functions as part of a 12VDC or 24VDC run, which lets it sit in line with the wiring between the power source and the Tresco fixtures. The 7 foot sensor range supports door-triggered control across the distance between the sensor and the moving door surface, which is useful on taller cabinets or wider doors where the edge moves further from the jamb. Because the operation is defined as door open, light on; door closed, light off, the sensor lets the door motion act as the trigger for the entire connected low voltage lighting circuit.
The controller is specified to handle all Tresco 12/24VDC single color dimmable low voltage lights, so one sensor style can be used whenever that light family is chosen, helping keep control behavior consistent across multiple openings. Its smaller design and 8mm diameter hole for recess mounting give a clear, repeatable drilling target, which aids production workflows where the same hole size can be drilled across many doors or frames. The nickel finish helps the installed sensor present a finished look in both residential and commercial millwork where hardware is visible during door movement. With the defined door open, light on; door closed, light off sequence, installers can wire the sensor knowing exactly how the lights will behave whenever the door cycles, which supports predictable demonstrations for end users and straightforward troubleshooting if the door motion ever fails to trigger the expected light response.
The PowerSync wired controller operates Tresco 12/24VDC single color dimmable low voltage lights, so it controls those fixtures as the door position changes.
The single door sensor is 12VDC and 24VDC compatible, allowing the same controller to be used on either low voltage system in a Tresco installation.
The door sensor is defined as door open, light on; door closed, light off, so the LED lights follow the door movement for simple user operation.
The sensor uses a smaller design with an 8mm diameter hole for recess mounting, giving a specific bore size when drilling into cabinet parts.
The door sensor lists a 7 foot sensor range, providing a defined distance window where door movement will trigger the connected lighting.
The nickel finish gives the sensor a neutral metal look that coordinates with many hinges and fittings, supporting a clean, finished appearance.
This PowerSync wired controller with single door sensor is built to run all Tresco 12/24VDC single color dimmable low voltage lights, giving you defined behavior of door open, light on; door closed, light off. The smaller sensor body, 8mm recess hole requirement, and nickel finish offer clear mounting dimensions and a finished look around the opening. For projects using Tresco low voltage lighting where door movement should directly govern light operation, this controller provides a focused option to tie cabinet or door motion to the lighting circuit.
Sold In: 1 Each
