Domino DF 500/700 Cross Stop is designed for use with Domino DF 500 and Domino DF 700 joiners, so it works directly with those Festool machines on the bench or in the shop. The cross stop plugs into the Domino edge guide, creating a fixed reference tied to the tool instead of relying on layout marks on the workpiece. That connection helps maintain consistent spacing when cutting multiple mortises along an edge, which supports uniform joints across cabinet parts or furniture rails. The cross stop supports repeat mortising at equal intervals, so once spacing is set, you can move from part to part without re-measuring each position. This setup reduces layout time and helps keep rows of mortises aligned, which is important when you are building matching panels, frames, or face components that must register cleanly in assembly.
The Domino DF 500/700 Cross Stop works by plugging into the Domino edge guide, so setup happens at the tool rather than on the stock. Once the cross stop is fixed to the edge guide, the joiner references from the same alignment point on every cut, which simplifies moving along a board edge or between duplicate parts. Because the cross stop is specified for repeat mortising at equal intervals, its adjustments are aimed at setting a spacing pattern that repeats from mortise to mortise. That pattern helps keep joints in line when cutting a series of slots for Domino connectors in carcass sides, shelves, or door frames, supporting precise assembly without shifting locations between cuts.
The Domino DF 500/700 Cross Stop is for use with Domino DF 500 and Domino DF 700, placing it directly in workflows that rely on these Festool joiners for loose tenon construction. By plugging into the Domino edge guide, the cross stop fits into operations where the edge of the workpiece is the primary reference surface, such as aligning mortises along cabinet sides, table aprons, or frame members. In those situations, the cross stop turns the joiner into a spacing tool as well as a cutting tool, because the edge guide and cross stop combination control both location and interval. The ability to support repeat mortising at equal intervals means it is suited to tasks like evenly spaced joints for shelving, multi-rail assemblies, or repetitive panel construction using the same Domino machine family.
The cross stop is designed to support repeat mortising at equal intervals, which directly affects how consistent a run of joints will be across multiple components. When the same spacing is used for each mortise, parts such as rails, stiles, and carcass panels line up more predictably during glue-up, because the Domino locations match from piece to piece. The way the cross stop plugs into the Domino edge guide means the spacing system stays attached to the tool, so each cut carries the same built-in offset rather than relying on fresh measurements. This approach helps maintain consistent spacing across a project, which can reduce fitting adjustments when connecting parts assembled with Domino DF 500 or DF 700 joiners. With the Festool 498590 part number, shops can specify this exact cross stop when standardizing mortise spacing methods on Domino-based joinery lines.
The Domino DF 500/700 Cross Stop is for use with Domino DF 500 and Domino DF 700 joiners, so it works directly with those Festool machines during mortise cutting.
The Domino DF 500/700 Cross Stop plugs into the Domino edge guide, creating a tool-mounted reference that travels with the joiner along the workpiece.
The Domino DF 500/700 Cross Stop supports repeat mortising at equal intervals, so once spacing is set, each mortise along an edge follows the same pattern.
The Domino DF 500/700 Cross Stop helps maintain consistent spacing, which keeps Domino joints aligned across matching parts and supports smoother assembly.
Festool part number 498590 identifies the Domino DF 500/700 Cross Stop, allowing straightforward reference when specifying, stocking, or replacing this spacing aid.
The Domino DF 500/700 Cross Stop plugs into the edge guide, so referencing and spacing stay tied to the tool, which can streamline runs of identical mortises.
The Domino DF 500/700 Cross Stop is built for use with Domino DF 500 and Domino DF 700 joiners, giving those tools a dedicated way to handle repeat mortising at equal intervals along edges. Because it plugs into the Domino edge guide, it provides a stable, tool-based reference that helps maintain consistent spacing without re-laying every joint. With Festool part number 498590, this cross stop slots cleanly into a Domino-focused workflow where uniform mortise spacing supports faster, more predictable joinery on cabinet, furniture, or fixture runs.
Sold In: 1 Each