Schaub Traditional Series satin nickel knob describes a solid brass cabinet knob designed for projects that need a traditional look with a defined feel at the pull point. The 1-1/2 inch diameter face gives fingers a broad gripping surface, which helps when operating heavier cabinet doors or drawers. The satin nickel finish presents a muted metallic surface that visually fits many cabinet finishes while also softening fingerprints in daily use. Solid brass construction provides a dense, weighty knob body, which supports a more substantial hand feel during frequent operation. The 1 inch base diameter transitions the knob to the door or drawer face in a defined footprint, which helps visually anchor it on stile-and-rail or slab fronts. A 1 inch projection sets the knob out from the surface, creating clearance for fingers without extending too far into working walkways.
The 1-1/2 inch diameter knob head defines the drilling layout because it determines visible spacing from door edges and adjacent hardware, which matters when aligning multiple knobs across a run of cabinets. A 1 inch base diameter keeps the contact area tight enough for narrow rail sections, which is useful on smaller doors or reduced-width drawer fronts. The 1 inch projection affects hand clearance at corner cabinets and near adjacent walls, which helps maintain comfortable operation where space is limited. The 8-32 x 1 inch screw size gives installers a known machine thread and shaft length, which works with standard cabinet boring patterns and typical door and drawer front thicknesses found in many woodworking jobs.
The Traditional Series identity places this satin nickel 1-1/2 inch diameter knob in projects where classic cabinet lines are important, such as framed kitchen cabinets, built-ins, and traditional bath vanities. The 1 inch base diameter creates a proportional step between the knob face and the door or drawer surface, which suits stile-and-rail profiles and raised-panel fronts that benefit from defined hardware transitions. Solid brass construction supports repeated pulling force on heavy drawers or door fronts, which is helpful in storage cabinets that carry tools, supplies, or dense contents. The satin nickel finish visually fits with other satin nickel decorative hardware and moldings, which simplifies coordinating the knob with hinges, pulls, and trim on the same elevation.
The fixed 1-1/2 inch diameter and 1 inch base diameter allow installers to set consistent centerlines from door edges, which helps keep knob placements visually aligned across repetitive cabinet runs. A 1 inch projection keeps the gripping point predictable relative to the door face, which aids in planning clearances near tall stiles, appliance panels, or adjacent walls. The 8-32 x 1 inch screw size spec informs drill bit and boring jig selection, which streamlines repetitive installations in shop environments where multiple doors and drawers are processed together. Solid brass material maintains thread engagement strength around the screw bore, which supports reliable mounting over ongoing cycles of opening and closing. The satin nickel finish establishes a stable surface tone, which helps designers and installers match this knob to other satin nickel components specified in the same project.
The Schaub 704-15 knob has a 1-1/2 inch diameter face, which offers a broad gripping area for operating cabinet doors and drawers.
The knob has a 1 inch projection, which sets the gripping surface out from the cabinet face for finger clearance without extending excessively.
The Schaub Traditional Series 704-15 knob is made from solid brass, which provides a dense, rigid body for repeated cabinet use.
This 1-1/2 inch cabinet knob has a satin nickel finish, which offers a muted metallic appearance suited to many cabinet and fixture combinations.
The knob has a 1 inch base diameter, which defines the footprint on the door or drawer front for layout and alignment.
The Schaub 704-15 knob specifies an 8-32 x 1 inch screw size, which matches common cabinet drilling and mounting practices.
The Schaub Traditional Series satin nickel 1-1/2 inch diameter knob combines solid brass construction, a 1 inch base, and 1 inch projection to support consistent cabinet layouts. Using the 8-32 x 1 inch screw specification, installers can align this knob with standard boring patterns across doors and drawers for unified appearance and predictable hand clearance in kitchens, baths, or built-in casework.