Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 8400 drawer member describes this 28 inch long drawer slide component that forms the moving part of a KV Model 8400 side mount assembly, so it lets drawers travel on ball bearings along a matching cabinet member track. The drawer member is identified as manufacturer part 8400-92 28, which ties it directly to the 8400 Series for consistent fit and performance wherever that series is specified. This drawer member is non-handed, so one part style can be used on either side of a drawer, which simplifies stocking and reduces the chance of orientation errors during layout. The member is designed as a full extension component, which allows the connected drawer to open out to the full slide length, helping bring stored contents fully forward for easier access when the complete 8400 slide set is installed.
This drawer member is part of a side mount ball bearing slide design, so it is intended to fasten along the vertical side of a drawer rather than beneath it, which influences how drawer box sides are sized and drilled. Recommended fasteners are #7 x 1/2 inch Phillips Truss Head screws (BST1/2X7-2C), so the installer can match screw diameter and head style to the slide holes and material thickness for a snug, low-profile attachment. Lever disconnect is listed as a feature on this drawer member, so the assembled slide can be separated at the lever point, which helps with finishing, transport, or service when drawers need to be removed and later reinstalled on the same tracks. A ball retainer latch feature is also specified, so the ball bearing carriage remains correctly positioned within the member, supporting consistent engagement when the assembled slide is cycled in normal use.
The KV Model 8400 28 inch length spec means this drawer member suits drawer boxes designed around a 28 inch full extension slide, so casework with deeper storage can maintain smooth reach across the full run. As a side mount component within the Side Mount Drawer Slides class, this member is suited to cabinet and furniture projects where slide hardware is placed along the sides, so builders can preserve vertical space under the drawer for structural rails or crossmembers. The 1/2 inch plus 1/32 inch minus 0 inch side clearance on each side defines the working gap between drawer and cabinet, so when drawers are built to that clearance, the slide can operate without binding while avoiding excessive side-to-side play. With a 1-13/16 inch member height, the part occupies a modest strip on the drawer side, so designers can balance structural side height with the clearance needed above and below the slide in multi-drawer stacks.
The non-handed design of this drawer member allows the same part profile to be installed on either the left or right drawer side, so assembly crews can work faster without sorting components by hand, which helps reduce picking errors on busy production lines. The noted 32 mm pattern supports use in system 32 cabinet construction, so shops running line-bored cases and drawers can position slides off existing hole rows, enabling consistent hardware placement from cabinet to cabinet. Lever disconnect on the member means drawers can be released at the disconnect point during assembly or finishing, so large or heavy drawers can be handled in stages rather than as a single loaded unit during case installation. The ball retainer latch stabilizes the bearing set in the member, so drawers track predictably along the slide even after repeated cycles, which supports long-term alignment in everyday opening and closing. The anochrome finish is applied across the member surface, so hardware in exposed or semi-exposed installations maintains a coordinated look with other anochrome-finished components from Knape and Vogt, which can be important in projects where hardware appearance is part of the visible design.
The 8400 drawer member is part of a side mount ball bearing slide system, so it works in applications where slides are mounted to the drawer sides for smooth, guided movement.
The Knape and Vogt 8400-92 28 drawer member has a 28 inch length, so it matches drawer designs planned around 28 inch full extension travel in the 8400 Series.
This drawer member is specified for 1/2 inch plus 1/32 inch minus 0 inch side clearance on each side, so drawer and cabinet widths can be sized for that running gap.
The 8400 drawer member is non-handed, so the same component profile can be used on either drawer side, simplifying part stocking and installation steps.
This Knape and Vogt drawer member is noted as using a 32 mm pattern, so it aligns with system 32 style drilling commonly used in cabinet production.
This drawer member lists #7 x 1/2 inch Phillips Truss Head screws, part BST1/2X7-2C, as recommended fasteners, so the fastener size and head style suit the slide holes.
The Knape and Vogt 8400 drawer member with anochrome finish, 28 inch length, and 1-13/16 inch height gives shops a defined component for KV Model 8400 side mount builds, so projects following that series can stay consistent from layout through installation.
Sold In: 50 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  KV8402 Mfr# 8402 | Rear Mounting Bracket for 8400 Series Slides, Zinc |
