Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Satin nickel cabinet knob construction in zinc die cast gives this piece a solid metal body that stands up to regular cabinet and drawer use, which matters on frequently used doors in kitchens, baths, or built-ins. The knob belongs to the Hickory Hardware Conquest collection, so the design stays consistent when repeating this part across a run of cabinetry. Its round 1-1/8 inch (29 mm) diameter face provides a comfortable fingertip grip that helps doors and drawers open smoothly without slipping. A projection of 1 inch sets the knob off the face of the cabinet enough for fingers to pull easily while keeping a low profile that stays close to the door surface. The 1/2 inch base diameter creates a defined footprint against the wood, which helps visually cover the fastener hole area on most cabinet doors and drawer fronts.
This Hickory Hardware Conquest knob uses an 8-32 x 1 inch screw size, which works with a widely used cabinet thread standard so installers can drive it into pre-drilled holes with familiar tools and bits. The 1-1/8 inch diameter and 1/2 inch base diameter give enough face and footprint to cover standard bore holes on most doors or drawer fronts, which helps keep the drilled area concealed after installation. With a 1 inch projection, the knob extends far enough from the cabinet surface to clear typical door edge profiles, so fingers can hook behind the knob without rubbing hard against the wood or laminate. The satin nickel finish and round profile pair well with straight or raised panel doors, allowing consistent visual spacing when these knobs are laid out along a bank of doors or drawers.
The Hickory Hardware Conquest Series satin nickel 1-1/8 inch diameter knob fits well on cabinet doors and drawer fronts where a moderate-size round pull is needed, because its 1-1/8 inch face balances grip and scale on common door widths. The zinc die cast material supports use on frequently opened kitchen wall and base cabinets, as the metal body accommodates the repeated pulls typical in those areas. In shop-built or custom woodworking projects, the 1/2 inch base diameter sits comfortably on standard 1-1/2 to 2-1/2 inch rails and drawer fronts, giving enough trim around the knob to show wood grain while still covering the drilled hole. The satin nickel finish helps the knob blend with many hinge and slide finishes used in cabinetry, so a run of these knobs can tie together mixed hardware sources on the same project. With a projection of 1 inch, the knob also suits vanity and utility cabinets where shallow clearances around doors call for a compact pull that will not stick out excessively.
The combination of a 1-1/8 inch diameter face and 1 inch projection on this Conquest knob gives installers a predictable geometry when laying out drilling patterns, since the centerline-to-edge distance stays consistent for multiple doors or drawers. Using the specified 8-32 x 1 inch screw size keeps the fastening method aligned with a common cabinet standard, which simplifies repeat work across banks of cabinets or multi-unit jobs that use the same knob. The 1/2 inch base diameter provides a reliable contact ring against the cabinet surface, which helps the knob seat squarely over the drilled hole and aids in keeping alignment straight during tightening. The zinc die cast construction keeps the weight of the knob moderate, so it does not place excessive stress on the screw threads when mounted on vertical doors. Across a full kitchen or casework install, these fixed dimensions and materials help create uniform sight lines and consistent hand feel from one opening to the next.
The P14255-SN knob has a 1-1/8 inch diameter, 1 inch projection, and a 1/2 inch base diameter, which helps it cover standard bore holes while staying compact on cabinet fronts.
The 1 inch projection holds the knob off the door surface enough for fingers to grip behind it, improving pull comfort while keeping the hardware close to the cabinet face.
The Hickory Hardware Conquest knob is made from zinc die cast, providing a solid metal body suited to repeated use on cabinet doors and drawers.
This Belwith Keeler knob has a satin nickel finish, giving a soft metallic look that coordinates with many common cabinet hinge and pull finishes.
The P14255-SN cabinet knob uses an 8-32 x 1 inch screw size, aligning with a widely used cabinet hardware thread for straightforward mounting in typical fronts.
This 1-1/8 inch diameter knob suits cabinet doors and drawers where a mid-size round pull is needed, such as kitchens, baths, or built-in casework.
The Hickory Hardware Conquest Series satin nickel 1-1/8 inch diameter knob P14255-SN combines zinc die cast construction, a 1 inch projection, and a 1/2 inch base diameter to give cabinets a consistent look and feel across doors and drawers. The 8-32 x 1 inch screw size supports straightforward mounting in typical fronts, which helps keep installation time predictable on multi-opening projects. For cabinet, casework, or woodworking jobs that call for a satin nickel round knob with these specific dimensions, this Belwith Keeler design from Wurth Baer Supply aligns well with repeatable layout and everyday use.