
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
4 x 3-1/16 coat hook polished brass gives you a decorative way to hang coats and hats while keeping a consistent finish across a project. This Berenson Corporation coat and hat hook is part of their premium line of decorative hooks, so it aligns well with higher-visibility residential or light commercial work. The hook is made of zinc with a polished brass finish, which provides a solid metal body with a bright, traditional brass appearance for face frames, panels, or wall boards. A one type, double prong design lets one hook handle multiple garments in tight spaces, which helps maximize hanging capacity on short runs of board. The base measures 1-1/16 inches, giving a compact footprint that still covers typical pilot holes in wood substrates. This decorative hook fits well where a small, finished detail helps tie together cabinetry, mudrooms, and similar spaces.
This 4 inch by 3-1/16 inch Berenson coat and hat hook uses four 8/32 x 1 inch installation screws, giving you a defined fastener size for planning substrate drilling and thread engagement. With a 1-1/16 inch base, the screw pattern stays tight to the centerline, which helps when mounting on narrow trim or cabinet ends. The polished brass finish on the hook ties into brass-finished fasteners, supporting a clean look around the base. The double prong layout keeps the load closer to the mounting surface, which can help distribution into wood when placed along studs, rails, or solid cabinet backs.
This Berenson decorative coat and hat hook sits in the Decorative Hooks class, so it suits visible locations on cabinetry and finished walls. The 4 inch length works well along mudroom boards, closet sides, and the ends of cabinet runs, giving enough reach for coats without overwhelming narrow panels. Its polished brass finish helps tie into brass knobs and pulls, so it can continue an existing hardware story through hallways, entry areas, or built-ins. The one type, double prong design supports stacking a coat and hat on a single hook, which is useful in smaller entry alcoves or behind doors where hook count is limited. The compact 1-1/16 inch base allows a series of hooks to be staggered along rails without consuming much face width.
The defined overall size of 4 inches by 3-1/16 inches gives installers fixed reference points for height and spacing, which helps when laying out straight, even runs along boards or cabinet backs. With four 8/32 x 1 inch installation screws, hole locations and screw length are known in advance, simplifying pre-drilling and keeping thread engagement consistent across different mounting locations. The zinc construction provides a uniform body for driving those screws, which can assist in achieving a snug fit against wood or similar substrates. The polished brass finish offers a repeatable color tone from hook to hook, important when lining multiple units in the same field of view. Because the hook is part of Berenson's premium decorative coat and hat hooks line, it can be specified alongside matching decorative hardware to streamline selection and maintain a coordinated finish schedule across an entire job.
The 4 x 3-1/16 coat hook polished brass measures 4 inches by 3-1/16 inches, giving clear height and projection references for planning hook spacing along walls or cabinetry.
The Berenson decorative coat hook is made of zinc with a polished brass finish, providing a solid metal body with a bright brass appearance for visible mounting locations.
The Prelude hook 4 inch brass uses a one type, double prong design, so each hook offers two hanging points for coats and hats on a single compact base.
The zinc hook for coats and hats uses four 8/32 x 1 inch installation screws, giving a defined thread and length for drilling and fastening into wood substrates.
This polished brass decorative hook is part of Berenson's premium line of decorative coat and hat hooks, aligning it with their broader decorative hardware offering.
The Berenson 8010-03-P hook has a 1-1/16 inch base, providing a compact footprint that covers typical pilot holes on rails, panels, or cabinet ends.
The 4 x 3-1/16 coat hook polished brass from Berenson Corporation combines zinc construction, a polished brass finish, and a one type, double prong layout for efficient coat and hat hanging. Defined dimensions, a 1-1/16 inch base, and four 8/32 x 1 inch installation screws provide clear reference points for planning and installing straight, repeatable hook runs on walls, rails, or cabinetry. Use this decorative hook when a compact footprint and consistent polished brass appearance matter across an entry, mudroom, or closet project.
Sold In: 1 Each