
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Amerock Ravino polished brass knob is a zinc die-cast cabinet knob designed for decorative hardware installations where a compact round pull is needed. The 1-1/4 inch diameter face provides a familiar hand grip that suits cabinet doors and drawer fronts in standard residential or shop-built casework. The polished brass finish delivers a bright metallic look that visually matches other polished brass decorative hardware on the same run of cabinets, which helps maintain a consistent appearance across multiple doors and drawers.
The knob projects 1-1/16 inch from the mounting surface, which sets a comfortable clearance between the cabinet face and the user's fingers during everyday opening and closing. A 1-1/4 inch width paired with a 15/16 inch base diameter spreads contact on the cabinet surface, which helps the load sit on a defined footprint around the mounting hole. The Amerock manufacturer part number BP530123 identifies this exact Ravino series design, which supports straightforward reorders or matching during future hardware changes.
This Amerock Ravino knob uses an 8-32 screw thread for attachment, which aligns with common cabinet knob mounting practices using a through-bored hole in the door or drawer front. The 1-1/4 inch nominal knob diameter works within typical 3 inch or wider rails and stiles, leaving space around the knob center for finger access. The 1-1/16 inch projection keeps the working grip zone tight to the face while still letting users pull at different angles.
The 15/16 inch base diameter defines the contact ring that seats against the finished cabinet surface, which matters when locating the bore so the base lands fully on flat material. Because the knob body is zinc die-cast, each unit retains the same Ravino profile and sizing, supporting predictable layout spacing when multiple knobs line up on drawer banks or tall cabinet runs.
The Amerock Ravino polished brass knob suits cabinets and casework where a 1-1/4 inch cabinet knob provides the right balance between grip and scale, such as standard kitchen doors, bath vanities, or shop-built storage. The round 1-1/4 inch diameter face gives installers a clear center point, which helps when aligning hardware across multiple fronts. The 1-1/16 inch projection keeps the user grip close to the door plane, which is useful on narrow walkways or tight galley layouts where extended pulls might catch clothing or bump adjacent surfaces.
The 15/16 inch base diameter sets a defined footprint around the mounting bore on the cabinet face, which helps the knob visually anchor smaller drawer fronts without overpowering them. Because the knob is part of the Amerock Ravino series, it visually aligns with other Ravino components that share the same design language, helping designers carry one style through several cabinet zones. The polished brass finish ties into other polished brass cabinet knob and hinge choices, supporting coordinated hardware planning in projects that feature brass plumbing or lighting trims.
The 8-32 knob installation thread standardizes the fastener interface, which streamlines boring and mounting workflows across large cabinet runs because the same hole preparation works for each Amerock Ravino cabinet knob. The 1-1/4 inch cabinet knob diameter gives installers a fixed reference dimension, which simplifies layout measurements from door edges or stile centers when repeating knob positions row after row.
The 1-1/16 inch projection keeps the pull point predictable relative to the cabinet face, which helps when aligning door reveals where deeper hardware might interfere with adjacent doors. The zinc die-cast cabinet knob construction keeps the Ravino profile consistent from piece to piece, which matters when doors and drawers are lined in grids and small variations in shape would stand out. With the base diameter at 15/16 inch, the contact area around the mounting hole remains controlled, which helps maintain a clean look on flat panel and shaker-style doors with minimal trim detail.
The Amerock Ravino zinc die-cast knob has a 1-1/4 inch diameter face, 1-1/16 inch projection, and a 15/16 inch base diameter, giving installers clear size references for layout on cabinet doors and drawers.
The BP530123 knob is made from zinc die-cast material with a polished brass finish, pairing a defined Ravino profile with a bright brass appearance for coordinated decorative hardware layouts.
The 1-1/16 inch projection sets the grip point close to the cabinet face, giving users enough finger clearance while keeping knobs from sticking far into walkways or tight spaces.
The Amerock Ravino cabinet knob uses an 8-32 thread, matching standard cabinet knob bored-hole installations and allowing a consistent fastening approach across multiple fronts.
The 1-1/4 inch diameter provides a compact, repeatable size that works on most cabinet rails and drawer fronts, helping installers keep knob spacing and alignment uniform across a project.
The Amerock Ravino series designation identifies this knob as part of the Ravino family, which helps designers and installers match this polished brass knob with other Ravino hardware pieces.
The Amerock Ravino polished brass knob, with its 1-1/4 inch diameter face, 1-1/16 inch projection, and 15/16 inch base diameter, gives cabinet installers defined measurements for consistent layouts. The zinc die-cast construction and polished brass finish align with decorative hardware expectations in kitchen, bath, or storage projects that call for brass cabinet details. When a project specifies the Amerock BP530123 part number, selecting this Ravino knob keeps sizing, finish, and thread details aligned with the planned cabinet hardware scheme.
Sold In: 1 Each