Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
1-1/16 inch diameter long mount flange from Knape and Vogt supports 1-1/16 inch OD tubing, so closet rods with that outside diameter sit properly in the flange for solid hanging performance. The flange is made of zinc, which gives the mounting base a rigid structure that resists deformation during installation and under everyday hanging loads. A chrome finish over the zinc body provides a clean, bright appearance that matches typical closet tubing finishes, helping built-ins and retrofits look consistent from rod to support. The part is identified as 735 CHR, so installers working from drawings or reorder lists can match this flange directly to specified hardware. Classified in closet rods and flanges, it fits standard closet build workflows where rods need secure, repeatable support at each end or along a span.
The flange is for 1-1/16 inch OD tubing, so rods with that outside diameter drop directly into the support without play, helping keep hangers running straight along the span. Screw holes located 2 inches on center define the fastening footprint, letting installers pre-mark hole locations on gables or end panels for consistent placement. Zinc material in the flange body supports firm tightening at each screw point, so the mounting pattern can be drawn snug to the surface without distorting the hardware. The chrome finish allows the visible face around the rod to blend with chrome tubing, supporting a finished look when flanges are mounted at eye level in open closet sections.
This Knape and Vogt closet flange is designed for 1-1/16 inch OD tubing, so it serves as a dedicated support for closet rods in that size range. In a typical closet or storage build, rods carry hanging garments or gear between two facing panels or walls. Using a flange matched to the rod diameter keeps the tubing seated at the correct height and alignment, which supports smooth sliding of hangers from end to end. Within closet rods and flanges hardware, this long mount flange ties the rod to the structure, transferring load from the tubing into the mounting surface. Because the part is a flange rather than a rod section, it focuses on endpoint and intermediate support, providing defined bearing points wherever the design calls for them along the run.
The 1-1/16 inch OD tubing specification on this flange gives installers a clear dimension to match when selecting or cutting rods, reducing guesswork around fit at the support points. Screw holes spaced 2 inches on center provide a fixed pattern that can be laid out repeatedly across multiple closets in a project, which supports consistent reveal heights and rod alignment from unit to unit. Zinc construction means the flange body stays rigid as screws are tightened, so installers can pull the flange firmly against panels without warping the mounting plate. The chrome finish offers a surface that remains visually consistent along the line of hardware, which matters when open closets or wardrobe interiors are part of a visible design scheme. Using the 735 CHR part number across drawings, purchase notes, and field installation keeps the same geometry in play from planning through final mounting.
The flange is for 1-1/16 inch OD tubing, so it supports closet rods with a 1-1/16 inch outside diameter for a snug, aligned fit at each support.
Screw holes 2 inches on center give a fixed fastening pattern, allowing consistent hole layout and repeatable positioning across multiple flanges on a project.
The flange is made of zinc, which provides a rigid mounting body that holds screw tension and resists distortion when rods and loads are applied.
The chrome finish gives the flange a bright, smooth surface that visually matches chrome closet rods, supporting a uniform appearance in finished closets.
The manufacturer part number 735 CHR identifies this specific Knape and Vogt flange, helping align specifications, ordering, and installation on closet projects.
Classified under closet rods and flanges, this part serves as the mounting point that transfers load from 1-1/16 inch rods into walls or panels.
Knape and Vogt 735 CHR long mount flange pairs 1-1/16 inch OD tubing support with a zinc body and chrome finish, giving closet builds a defined mounting point that aligns structure and appearance. Using the 2 inch on center screw pattern, installers can repeat flange locations accurately from opening to opening. For closet rod runs built around 1-1/16 inch outside diameter tubing, this flange supplies the sized seat and mounting footprint that keep rods positioned and ready for daily hanging loads.
Sold In: 1 Each
