Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Virtuoso satin nickel knob provides a defined 1-1/8 inch length and 1-1/8 inch width, giving cabinet doors and drawers a compact, easy-to-grip pull point that keeps fronts clean while still offering solid hand contact on every use. The zinc die cast material forms a rigid knob body that holds its shape under repeated pulls, supporting consistent alignment across a run of cabinets. A satin nickel finish creates a muted metallic look that softens reflected light, helping fronts read evenly in both bright shops and finished interiors. The knob design sits at a 7/8 inch projection, so it stands off the face enough for fingers without reaching too far into tight traffic paths. With a defined base area, this knob anchors visually to the door or drawer surface, supporting straight layout lines in hardware runs.
The M4 x 45mm screw size specification identifies the thread and shaft length used with this Berenson knob, which helps installers align drilling and driver selection to common cabinet construction. The 3/8 inch base diameter concentrates the contact area at the mounting hole, which supports solid seating against door or drawer faces during tightening. With a 7/8 inch projection and 1-13/16 inch overall length and width, installers can lay out hardware spacing knowing exactly how far the knob will extend and how much face area it will visually occupy. The consistent 1-1/8 inch nominal length and width reference ties these dimensions to a familiar cabinet knob size category, aiding planning when coordinating with existing layouts.
This Berenson Virtuoso Series satin nickel knob suits cabinet doors and drawers that call for a compact pull point with a defined square footprint. The 1-1/8 inch stated length and width keep the knob visually tight to the front, which works well on face frames, narrow rails, and smaller drawer fronts where oversized hardware might crowd edges. The 1-13/16 inch length and width specification describes the full dimension of the knob body, giving it presence on standard kitchen and bath cabinets without overpowering panel details. With a satin nickel finish, this knob aligns with typical satin nickel hinges, pulls, and other decorative hardware in the same color tone, supporting uniform hardware selection across a room. The 7/8 inch projection means the knob stands far enough off the surface for a comfortable pinch grip on both doors and drawers. Because this knob is part of the Virtuoso Series collection, it can be used wherever that series is specified to maintain a consistent design language from base cabinets to uppers.
The zinc die cast material of this Berenson 7139-1015-C knob provides a stable, molded form that keeps edges and faces consistent from piece to piece, which helps align sightlines when multiple knobs are installed in rows. The M4 x 45mm screw size specification pairs the knob with a common metric fastener length, supporting straightforward through-bore work in many cabinet side and drawer front thickness ranges. The 3/8 inch base diameter focuses clamping pressure close to the mounting hole, helping the knob seat flat against the surface during tightening. With a 1-13/16 inch length and width and 7/8 inch projection, installers can rely on repeatable spacing from door edges and drawer tops, which aids in setting jigs or templates for multiple cabinets on a job. The 1-1/8 inch nominal length and 1-1/8 inch width reference provide a quick size shorthand, which helps tradespeople pair this knob logically with other hardware sizes when planning layouts.
The Berenson 7139-1015-C knob has a stated 1-1/8 inch length and width, with an overall 1-13/16 inch length and width, giving both a compact footprint and full body size for layout planning.
The Virtuoso Series satin nickel knob has a 7/8 inch projection, providing enough stand-off for a comfortable grip while keeping hardware close to the cabinet face.
The Berenson Virtuoso Series knob is made from zinc die cast, giving the knob a rigid, molded construction suited to repeated opening and closing of cabinet doors and drawers.
This Berenson cabinet knob uses a satin nickel finish, providing a subdued metallic appearance that coordinates with other satin nickel decorative hardware components.
This satin nickel knob is part of the Virtuoso Series collection, linking it to other knobs and pulls in the same design family for coordinated cabinet hardware projects.
The Virtuoso Series knob is specified with an M4 x 45mm screw size, aligning the knob with a common metric cabinet fastener standard for straightforward mounting work.
The Berenson Virtuoso satin nickel knob combines zinc die cast construction, a 1-1/8 inch nominal size, and a 7/8 inch projection to support practical cabinet door and drawer operation. The matched 1-13/16 inch length and width give a balanced footprint that suits many cabinet styles, from small bath vanities to full kitchen runs. With its Virtuoso Series collection identity and satin nickel finish, this knob fits projects where a unified hardware family and consistent color tone are important. Use these defined dimensions and material details to align your next cabinet hardware selection with the functional and visual targets of your job.
