Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Opus Series satin nickel knob gives cabinets a defined pull point with a 1-3/8 inch length that suits door and drawer fronts needing a compact hand grip. The 1-3/16 inch width spreads that grip area, so fingers catch the knob quickly on everyday reaches. A 7/8 inch projection brings the knob out from the front, which creates finger clearance without pushing hardware too far into walk paths. The satin nickel finish provides a muted metal look that works in both traditional and modern cabinet runs. Zinc die cast construction forms the core of this knob, giving a consistent shape that supports repeat installations across a full kitchen or bank of casework. The Opulence Series collection tie-in helps keep visual lines consistent when matching this knob with other Berenson hardware pieces.
This Berenson Opus Series satin nickel knob uses an M4 x 45mm screw size, giving a familiar metric thread that aligns with typical cabinet drilling setups in many shops. The zinc die cast material provides a stable threaded area around that screw engagement, which helps the knob seat squarely to the door or drawer face when tightened. With its 7/8 inch projection, this knob pairs well with standard cabinet face thicknesses where a modest stand-off is preferred. The 1/2 inch base diameter concentrates pressure close to the fastener location, supporting a firm contact area against the surface during installation. The combination of 1-3/8 inch length and 1-3/16 inch width keeps the knob centered over the bore while still leaving enough edge distance on most face frames and slab fronts.
The satin nickel finish on this Berenson Opus Series satin nickel knob suits cabinet layouts where a soft metallic tone is preferred over bright polished hardware, helping it coordinate with satin nickel hinges and pulls. Its classification under Decorative Hardware & Moldings and Knobs places it in standard cabinet knob workflows, so it can be worked into kitchens, baths, and casework that follow common drilled hole practices. The 1-3/8 inch length and 1-3/16 inch width proportions create a balanced profile on typical door rails and drawer fronts, avoiding an oversized look on smaller fronts. As a Berenson Corporation product in the Opulence Series, this knob can be matched visually with other Opulence Series pieces on nearby doors or drawers that share the same finish. The zinc die cast construction maintains a consistent external contour from piece to piece, which supports uniform appearance when multiple knobs are installed in straight lines or grid layouts.
The specified M4 x 45mm screw size on this satin nickel 1-3-8 inch cabinet knob means installers work with a known thread pattern, supporting predictable driving torque and grip in the knob body. The 7/8 inch projection defines the stand-off from the front, helping layout decisions where clearance from adjacent doors, trim, or appliance fronts is a consideration. A 1/2 inch base diameter at the contact point keeps the load close to the screw centerline, supporting firm seating of the knob against the door or drawer face. The measured width of 1-3/16 inch and length of 1-3/8 inch work together to keep the hand contact area centered over the mounting bore, which can reduce twisting forces on the screw under repeated use. The zinc die cast material gives the knob a solid, unified body around the threaded area, which supports repeated opening and closing cycles along typical cabinet use patterns.
The Berenson Opus Series satin nickel knob has a 1-3/8 inch length, 1-3/16 inch width, 7/8 inch projection, and a 1/2 inch base diameter, giving it a compact, balanced footprint on cabinet fronts.
The Berenson Opus Series satin nickel knob is made from zinc die cast material, providing a formed metal body that supports consistent shape and finish across multiple knobs.
The Berenson Opus Series satin nickel knob uses an M4 x 45mm screw size, giving installers a specific metric thread and length to match standard cabinet drilling practices.
The Berenson Opus Series satin nickel knob projects 7/8 inch from the cabinet surface, offering finger clearance while maintaining a low-profile appearance on the door or drawer.
The Berenson Opus Series satin nickel knob features a satin nickel finish, matching other satin nickel decorative hardware components in many cabinet installations.
The Berenson Opus Series satin nickel knob carries manufacturer part number 7170-1015-C, identifying this specific size, material, collection, and finish combination.
The Berenson Opus Series satin nickel knob, part number 7170-1015-C, combines a 1-3/8 inch length, 1-3/16 inch width, and 7/8 inch projection to suit many cabinet door and drawer layouts. The zinc die cast construction and satin nickel finish align with decorative hardware needs where a consistent look across multiple openings is important. With its M4 x 45mm screw size and defined base diameter, this knob fits neatly into standard knob boring and fastening routines. For projects calling for Opulence Series styling in satin nickel, this cabinet knob offers a clear, measured option.
Sold In: 1 Each
