Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Blum #6 x 1/2 inch truss head installation screw is sized and shaped specifically for mounting European cup hinges and drawer slides to cabinet panels. The wide, low-profile truss head seats flat against mounting plates without over-penetrating, and the coarse thread bites cleanly into plywood, MDF, and particleboard cabinet boxes.
European cup hinges and most side-mount drawer slides ship with pre-drilled mounting holes sized for a #6 screw. The 1/2 inch length is the standard for 3/4 inch cabinet panel stock — long enough to hold firmly without punching through the back face or piercing a finished interior. The truss head's wide diameter spans the clearance holes in most hinge mounting plates and slide brackets, pulling the hardware tight and flat without rocking or tilting. That consistent seating matters most when you are hanging doors or aligning drawer runs, where even a slightly canted hinge plate affects gap and swing.
The zinc plating on this screw is a good match for dry cabinet interiors. It handles the contact and light moisture exposure typical of kitchen and bath cabinetry without surface rust that would stain a white melamine box. This screw is intended for interior cabinet use. For installations in high-humidity or wet areas, confirm that the finish and panel material are rated for the environment before specifying.
Cabinet shops building face-frame and frameless boxes keep a box of these on hand alongside their Blum hinge and slide orders. Installers doing kitchen or bath retrofits use them when swapping out old hardware for new Blum components. The 100-piece box is sized for a medium install — enough to cover a full kitchen's worth of hinges and a few drawer runs without opening multiple containers. Because these are sold as a matched Blum product, there is no guesswork about head fit or gauge when working with standard Blum hinge and slide mounting plates.
The truss head's extra-wide, low-profile flange spans the clearance holes in hinge and slide mounting plates more fully than a pan head, distributing the clamping load and keeping the hardware seated flat against the panel. A pan head works in a pinch, but the truss head is the correct fit for most Blum mounting plate geometries.
No. At 1/2 inch, the screw engages well into the panel without reaching the back face on standard 3/4 inch stock. That makes it the right length for mounting hardware to cabinet sides, face frames, and interior panels without risk of breakthrough on finished surfaces.
The #6 x 1/2 inch truss head Phillips is a standard gauge and head type for European hinge and drawer slide mounting generally. It is sold as a Blum product and is a direct match for Blum mounting plates, but the same gauge, head, and length will fit most other European-style hardware with standard #6 mounting holes.
The coarse thread is designed for wood-based panel products: plywood, MDF, and particleboard. These are the most common substrates in cabinet box construction. For metal mounting tracks or panels, a different thread type and point are required.
Reaching for the correct mounting screw at the start of an install takes one variable off the table. The Blum #6 x 1/2 inch truss head Phillips gives you the head geometry, gauge, length, and thread matched to how European hinges and drawer slides are designed to mount, so the hardware seats correctly the first time.
Sold In: 100 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  BP295370021 Mfr# 295.3700.21 | Tandem Plus Rear Socket for 9" Slides, Screw-On, Depths 10-15/32" to 11-3/32 | ||||
Sold in: 1 Each |  BP2982200 Mfr# 298.2200 | Door Protector for Pull-Out Roller Wheels | ||||
Sold in: 1 Each |  BPZSB009001 Mfr# ZSB.0090.01 | Metabox Center Support Bracket for Wide Drawers, Zinc-Plated | ||||
Sold in: 1 Each |  BP295370022 Mfr# 295.3700.22 | Tandem Plus Rear Socket for 9" Slides, Screw-On, Depths 11-5/32" to 11-25/32 | ||||
Sold in: 1 Each |  BPZSB004501 Mfr# ZSB.0045.01 | Metabox Drawer Front Support Bracket for Interior Roll Out Trays, Zinc-Plated | ||||
Sold in: 1 Each |  BPZ30B000S04-WHA Mfr# Z30B000S.04 | Tandembox Rear Fixing Bracket Set, B-Height, Gray |