Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
3rd Hand Tall Support System is a jack system that enables you to support materials such as crown molding and drywall overhead and to create dust barriers, so one person can hold pieces in place while fastening or cutting. The single jack can support up to 150 lb, giving dependable temporary support for tasks like positioning long drywall sheets or holding trim while aligning joints. The extension range from 57 inches in the closed position to 144 inches in the fully open position lets you work between standard room heights and taller spaces without changing tools. The system is sold as a 3rd Hand, 5-foot 2 pack, so you can brace both ends of a workpiece or set up a straight dust barrier line along a work area. This setup turns ceiling-height tasks into a controlled, repeatable process.
The Fastcap 3rd Hand support extends from 57 inches to 144 inches, so setup starts with placing the closed or partially extended jack between the floor and the work surface location. The ergonomic pump handle then raises the jack in 1/2 inch increments, allowing careful approach to the ceiling or framing until firm contact is reached. The 3 inch by 3 inch articulating feet on top and bottom pivot to match the angle of the floor or surface above, helping the load spread across the pad rather than on an edge. With the 5-foot 2 pack configuration, you can position two supports along a run of crown molding or drywall, then fine-tune each jack height incrementally to bring the work into plane before fastening.
The 3rd Hand Tall Support System is designed to support materials overhead and to create dust barriers, so it fits into tasks where a stable temporary post is needed between floor and ceiling. The 57 inch to 144 inch extension range lets it operate in many interior spaces, from areas where the starting point is around 5 feet off the floor up to taller ceilings, so crews can move the same supports from room to room. When working with drywall, the 150 lb single jack capacity keeps standard sheet sections held in place while you fasten edges or locate framing. For crown molding or similar trim, the jacks hold the profile tight to the ceiling line so hands stay free for nailing and checking reveals. In dust barrier use, the dust barrier feet help support sheeting at the top and bottom contact points while you lay out a controlled work zone.
The Fastcap 3-H 2PK 3RD HAND 5 foot configuration, described as a 3rd Hand, 5 foot 2 pack, provides two tall support jacks that can be spaced along a workpiece, giving more even support than a single post in the center. The ergonomic pump handle that adjusts in 1/2 inch increments lets you bring each end of a board or panel up in small, predictable steps, which helps keep joints tight and surfaces level during fastening. The 3 inch by 3 inch articulating feet on both top and bottom widen the contact area and pivot to match the contact surfaces, helping the load transfer smoothly without concentrating force on corners. This articulation is useful when working against slightly irregular ceilings or floors, because the feet can rotate to maintain flat contact as you pump to final height. The 150 lb rating per jack sets a clear working range for the materials that can be supported, which supports consistent setup choices on similar jobs.
The 3rd Hand Tall Support System extends from 57 inches in the closed position to 144 inches fully open, so it spans many interior floor-to-ceiling distances for overhead support tasks.
The single 3rd Hand jack can support up to 150 lb, which suits many drywall panels and trim assemblies during positioning and fastening overhead.
The Fastcap 3rd Hand support uses an ergonomic pump handle that adjusts the jack in 1/2 inch increments, giving controlled height changes for tight fits at ceilings or framing.
The 3 inch by 3 inch articulating feet on top and bottom pivot to sit flat on angled or uneven surfaces, spreading load and helping the jack stay stable under pressure.
The jack system is described as enabling dust barriers, and the dust barrier feet support sheeting contact points to form temporary separation around work areas.
The SAP description states 3rd Hand, 5 foot 2 pack, which indicates this configuration provides two 3rd Hand tall support units for use together on a project.
The Fastcap 3rd Hand Tall Support System, 57 inch to 144 inch Extension, gives a single jack capacity of up to 150 lb, an ergonomic pump handle with 1/2 inch increments, and 3 inch by 3 inch articulating feet, so overhead materials and dust barriers can be positioned and held with controlled, repeatable pressure. The 3rd Hand, 5 foot 2 pack setup adds a second support jack, letting you brace both ends of panels or trim using the same adjustment method. Choose this Fastcap 3-H 2PK 3RD HAND 5 foot system when you want one material handling setup for overhead drywall positioning, crown molding support, and jobsite dust barrier layout.
Sold In: 1 Package