Wurth #7 x 5/8 Flat Head Screw For Hinge And Slide Work

Wurth #7 x 5/8 flat head screw is a case hardened Phillips-drive fastener designed for hinge and drawer slide installation jobs where a secure bite is needed. The sharp point coarse thread design drives into material quickly, which speeds up repetitive installation work on projects that use suitable substrates. The flat head profile seats flush when properly countersunk, which helps hardware sit tight against the mounting surface and supports consistent alignment. The #2 Phillips drive interface matches common driver bits, which keeps tool changes minimal on site or in the shop. Bright zinc finish identified in the description provides a clean, uniform screw appearance that suits typical hardware applications where a zinc-colored fastener is preferred.

Key Details That Support Hardware Installation

• The #7 diameter and 5/8 inch length described combine to give a compact fastener that grips well while staying short, which helps when mounting hinges or slides where screw depth is limited by material thickness.
• Case hardened construction referenced in the description provides a tough shank and head surface, which supports consistent driving with #2 Phillips bits and reduces the chance of deforming the drive recess during installation.
• The sharp point coarse thread detail lets the screw start and pull in aggressively, which is useful when installing hardware into compatible materials and aiming for faster, repeatable driving with power tools.
• The flat head form described sits down into a proper countersink on hinges and drawer slides, which helps the hardware sit flat against the workpiece and supports accurate door or drawer alignment.
• The bright zinc finish indicated in the description provides a standard plated appearance, which coordinates with typical zinc-colored hinges and slides for a visually consistent hardware layout.

Installation Fit With #2 Phillips Drive Workflow

The specified #2 Phillips drive on this Wurth screw lines up with a widely used bit size, which lets installers stay on one driver setup through long hinge and drawer slide runs. The sharp point coarse thread works with this drive style by pulling the screw into suitable material with minimal pre-driving effort, so each fastener sets quickly once the bit is engaged. The flat head configuration is shaped for standard countersunk hardware holes, which allows hinges and slides to clamp firmly to the surface when the screw is driven to depth. Case hardened construction supports this workflow by keeping the drive recess and head more resistant to wear under repeated bit engagement.

Using This Screw In Hardware Mounting Runs

Where This Sharp Point Screw Fits Best

The product description identifies this part as a hinge and drawer slide installation screw, which positions it for cabinet and furniture hardware mounting roles that match those hardware types. The #7 diameter stated offers a solid grip in many hinge and slide hole patterns that accept that size, so the screw can anchor the hardware firmly when driven to full depth in compatible materials. At 5/8 inch length, the screw suits situations where hardware needs secure holding power without excessive penetration, which can be important in thinner workpieces or face frames that match that depth range. The bright zinc plating described gives the screw a finish that pairs well with zinc-colored hinges and slides, which keeps visible fasteners visually consistent across a run of doors or drawers.

Why The Verified Details Matter In Use

The case hardened designation in the description means the screw is prepared for repeated driving loads, which supports installers working through large hardware runs using #2 Phillips bits without constantly dealing with damaged heads. The sharp point and coarse thread combination described help the screw start easily and pull in strongly, which keeps each installation cycle shorter when attaching hinges and slides to suitable substrates. The flat head style stated is designed to nest into countersunk hardware holes, which helps the hinge or slide flange draw tight and sit correctly, supporting smoother door and drawer action when the overall system is set up properly. The manufacturer part number 9191 clearly identifies this specific screw configuration, which helps shops and field crews reorder the same fastener for consistent results across multiple projects.

Common Questions About This Wurth Installation Screw

Selecting This Screw For Hardware Installation Runs

This Wurth #7 x 5/8 flat head screw combines a case hardened body, #2 Phillips drive, sharp point coarse thread, and bright zinc finish to support hinge and drawer slide installations that match its size. The defined 9191 part number from Wurth Baer Supply lets shops and installers rely on the same fastener configuration from job to job when they want repeatable hardware mounting performance using this screw type.