Schaub Siena Series ancient bronze knob gives cabinet doors and drawers a 1-3/8 inch diameter round pull point, so hands land in a predictable spot every time. The zinc die cast construction forms a solid-feeling knob body, which supports repetitive daily use on kitchen, bath, or built-in cabinetry. Its ancient bronze finish defines the visual tone on the face of the knob, helping tie in with other bronze-finished decorative hardware on the same run. A base diameter of 3/4 inch sets the footprint against the cabinet surface, which helps installers align the knob cleanly on narrower rails and stiles. The 1 inch projection establishes stand-off from the door or drawer face, giving fingers clearance to grip without contacting the wood finish. A width of 1-1/2 inches offers a comfortable grasp point, useful on both doors and medium-size drawers.
The 1-3/8 inch diameter of this Schaub and Company knob sets the main face size installers see when laying out hardware across doors and drawers, which helps line up knobs evenly on wide and narrow fronts. With a 3/4 inch base diameter, the contact circle stays inside most standard rail widths, which supports centered placement even on slimmer frame members. The 1 inch projection creates a defined offset from the cabinet surface, which allows users to pull without knuckles rubbing the door or drawer face. A 1-1/2 inch width defines the overall span of the knob head, which matters when spacing multiple knobs on larger doors so they do not visually crowd each other. The 8-32 x 1 inch mounting screw size establishes a common machine thread, which helps the knob integrate into standard cabinet construction using that screw specification.
This Schaub Siena Series ancient bronze knob functions as a round pull point for cabinet doors and drawers, which suits installations where a compact, circular grip is preferred over longer pulls. The 1-3/8 inch diameter offers a proportion that fits typical base and wall cabinet fronts, which keeps the knob visually balanced on both small doors and moderate drawer widths. Its 1 inch projection holds the grasp point off the face enough that fingers can hook behind the knob, which is useful on heavier doors that need a confident pull. The 3/4 inch base diameter keeps the footprint tight, which allows the knob to sit comfortably on rail-and-stile constructions without overlapping molded profiles. With the 1-1/2 inch width defining the knob span, this part fills the hand more than very small knobs, which can help with frequent opening on task areas such as prep zones or vanity cabinets.
The consistent 1-3/8 inch diameter lets installers repeat the same centerline layout across a whole room, which simplifies drilling jigs and speeds through-runs on multiple fronts. Because the knob is zinc die cast, each piece is formed to the same basic dimensions, which supports uniform alignment when rows of doors use the same part. The ancient bronze finish is specified as the surface treatment on this knob, which allows designers to specify this exact color tone across all Schaub and Company pieces using the same finish name. A 3/4 inch base diameter sets a known landing area at the back of the knob, which helps keep the bearing surface fully on flat sections of the door or drawer front. The 1 inch projection remains constant from the cabinet face, which produces an even shadow line when viewed down a bank of cabinets. Using the 8-32 x 1 inch screw size standardizes the mounting interface, which can streamline tooling and bit selection on shop assembly benches.
The Schaub Siena Series ancient bronze knob has a 1-3/8 inch (35 mm) diameter, which sets the main face size seen on the cabinet door or drawer front.
The ancient bronze round knob projects 1 inch from the cabinet surface, which provides finger clearance for a comfortable grip when opening doors and drawers.
The Schaub and Company 250-ABZ cabinet knob is zinc die cast, which creates a solid, consistent body for repeated daily use on cabinet fronts.
This ancient bronze round knob has a 3/4 inch base diameter, which keeps the contact area compact for fitting on standard cabinet rails and stiles.
The knob is specified with an 8-32 x 1 inch screw size, which defines the machine thread and length used for mounting through typical cabinet doors and drawers.
The Schaub ancient bronze knob has a 1-1/2 inch width and 1 inch projection, which balance a full grip surface with a compact stand-off from the cabinet face.
The Schaub Siena Series ancient bronze knob brings a 1-3/8 inch round pull point, zinc die cast construction, and a 3/4 inch base together in one part, which supports clean layouts across cabinet runs. With a 1 inch projection and 1-1/2 inch width, the knob supplies comfortable finger clearance and a stable grip on both doors and drawers. Selecting this 250-ABZ part number lets installers and shops repeat the same dimensions, finish, and 8-32 x 1 inch mounting interface throughout a project, which helps maintain visual alignment and consistent handling from cabinet to cabinet.