Schaub Traditional Designs Series knob is a round ring knob in antique brass that gives cabinets a classic look without adding visual bulk. The 1-1/4 inch diameter creates a comfortable grip area, which helps when opening heavier cabinet doors or deep drawers. The solid brass material provides a dense feel in hand, giving a sturdy pull point on frequently used fronts. The antique brass finish presents a warm, aged tone, which works well when tying in with traditional hinges or other brass hardware on the same run. A 7/8 inch projection holds fingers away from the cabinet face, helping reduce knuckle scraping against door edges while still keeping the hardware tight to the panel. The Schaub and Company branding signals a coordinated Decorative Hardware & Moldings solution across multiple knobs and pulls in the same space.
The 1-1/4 inch diameter sets this cabinet knob up for use on both doors and medium-width drawer fronts where a standard-size pull point is needed. The 7/8 inch projection keeps the gripping surface away from the cabinet face enough for a stable hold, which helps when pulling deep drawers or wider doors. The specified 8-32 x 1 inch screw size matches a common cabinet hardware thread, which lets installers plan their drilling pattern and fastening sequence using familiar tooling and processes. The antique brass finish and Traditional Series styling keep the visual profile consistent across multiple cabinet elevations in the same room.
The 1-1/4 inch diameter and round ring design position this knob for use on kitchen, bath, and built-in cabinets that call for a classic look. The antique brass finish suits traditional interiors where a warm tone is preferred over bright metal, which helps bridge between older hinges and newer hardware on retrofit jobs. In cabinet runs with raised-panel doors, the 7/8 inch projection creates finger clearance over edge profiles, which supports comfortable operation on thicker fronts. On drawer banks, the solid brass build supplies a firm pull point that handles the repeated load of opening loaded drawers without feeling light or flimsy. Within Decorative Hardware & Moldings projects, this knob aligns with the Traditional Series, which lets designers repeat the same profile across multiple cabinet types for a unified appearance.
The specified 1-1/4 inch diameter gives installers a predictable footprint to lay out across doors and drawers, which simplifies spacing when aligning multiple knobs on a long run. The 7/8 inch projection defines how far the knob stands off the surface, which helps installers anticipate clearance around adjacent doors, panels, or trim. The 8-32 x 1 inch screw sizing confirms a standard thread and length, which supports straightforward pilot drilling and fastening through common cabinet door thicknesses. The solid brass material responds consistently under tightening torque, which helps avoid distortion around the mounting point. The antique brass finish provides a stable visual reference, so when multiple 711-AB knobs are laid out on a bank of doors, the hardware reads as a coordinated field rather than a mix of styles. The Traditional Designs Series identity lets cabinet shops specify this knob across repeat projects where the same look and dimensions are needed again.
The Schaub 711-AB knob has a 1-1/4 inch diameter, giving a standard-size grip that suits both cabinet doors and most drawer fronts in typical residential layouts.
The knob projects 7/8 inch from the cabinet face, creating enough finger clearance for a solid pull while keeping the hardware close to the door or drawer.
The Schaub 711-AB knob is made from solid brass, providing a dense feel and stable pull point suitable for frequently used cabinet doors and drawers.
The knob uses an antique brass finish, giving a warm, traditional appearance that pairs well with classic cabinet styles and other brass hardware.
The 711-AB knob is specified with an 8-32 x 1 inch screw size, matching a common cabinet hardware thread for straightforward installation on standard doors.
The 711-AB knob is part of the Traditional Series from Schaub & Company, aligning with other Decorative Hardware & Moldings options for coordinated projects.
The Schaub Traditional Designs Series knob in antique brass combines a 1-1/4 inch diameter, 7/8 inch projection, and solid brass construction, giving cabinet professionals a predictable pull point for both new builds and upgrades. The 8-32 x 1 inch screw specification and Traditional Series styling support repeatable layouts across multiple doors and drawers. For projects calling for an antique brass round ring profile, this 711-AB knob provides the defined dimensions and finish needed to keep cabinet runs consistent from one opening to the next.