LED low voltage puck extension power cord describes a 15 foot extension power cord with a roll switch and 5 outlets that is designed for use with LED low voltage pucks. The cord extends reach from the power source to the LED puck runs, which helps when layouts place pucks away from an outlet or control point. The built-in roll switch controls the connected LED pucks from a single, accessible location, improving day-to-day operation on installed lighting runs. The 5 outlets along the cord accept any of the LED pucks above, so up to 5 pucks can plug into one cord for a compact, organized power path. This configuration concentrates power connections, which reduces scattered cords around cabinets or display areas and streamlines how the lighting system ties into the rest of the project.
The 15 foot extension power cord provides distance between the primary power source and the LED low voltage pucks, which lets installers route the line along cabinet backs, toe kicks, or casework runs without relocating the outlet. The roll switch located on the cord places control along that path, so the switch position can be selected to match how occupants access the cabinetry or display zone. The 5 outlets distributed on the cord give connection points for up to 5 LED pucks above, so each puck taps into the same feed without separate lines. Because the cord is part of the LED low voltage puck setup, its layout is planned alongside puck spacing and orientation, which keeps the wiring path consistent with the lighting design.
The Hardware Concepts, Inc. 5.90600-014 part is a 15 foot extension power cord with roll switch and 5 outlets, for use with LED low voltage pucks. This puts the cord into under-cabinet, display, or similar low voltage puck lighting runs that already specify LED pucks above. The cord sits between the power source and the puck locations, so its 15 foot reach spans from an outlet or power entry point to the area where the LED pucks mount. Because the cord provides 5 outlets along that length, a single run serves up to 5 pucks, keeping the lighting group tied to one control position. The roll switch on the cord becomes the user interface for that group, which places both power distribution and switching in the same assembly for straightforward planning.
The 15 foot extension length matters because LED low voltage pucks are often spaced along longer cabinet banks or shelving, and this distance lets the same cord support pucks spread across that span without additional power lines. The 5 outlets are important because they define capacity for up to 5 pucks, which gives a clear limit when designing how many fixtures tie to one run and supports predictable loading of that cord. The roll switch along the cord influences workflow by setting a single control for the connected LED pucks, so turning the lighting on or off happens at that switch rather than at each puck. Being designated for use with LED low voltage pucks aligns the cord with those fixtures, which supports building a low voltage puck system where power distribution and switching are matched to the same lighting family.
The extension power cord is for use with LED low voltage pucks, which directs it to low voltage puck lighting runs in cabinet, display, or similar applications using those specific LED pucks.
The extension power cord has 5 outlets that allow up to 5 LED low voltage pucks above to plug into one cord, so a single run can power and control a small group of fixtures.
The extension power cord is 15 feet long, which gives reach from a power source to LED low voltage puck locations spread along cabinets or displays within that distance.
The roll switch built into the 15 foot extension power cord controls the LED low voltage pucks connected to its 5 outlets, providing a single on-off control point along the cord.
The 5.90600-014 number identifies the Hardware Concepts, Inc. 15 foot extension power cord with roll switch and 5 outlets, which distinguishes this specific LED low voltage puck cord model.
Using one 15 foot extension power cord with 5 outlets groups up to 5 LED low voltage pucks on a single feed, which organizes the power path and simplifies routing along the cabinet run.
The 15 foot extension power cord with roll switch and 5 outlets from Hardware Concepts, Inc. is built for use with LED low voltage pucks, which aligns with projects already using those puck fixtures. The cord length, outlet count, and integrated roll switch all work together so up to 5 LED pucks above connect to one controlled run, supporting clean layouts and grouped operation. When a lighting plan calls for a defined number of LED low voltage pucks within a 15 foot reach of the power source, this 5.90600-014 extension power cord ties those fixtures into a single, organized line that supports straightforward installation and everyday use.
Sold In: 1 Each