Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Capital City Counters edge molding 3692 is a laminate edge molding designed to finish and protect countertop or work surface edges. The Labrador Granite Etchings pattern ties into laminate surfaces using that same look, which helps keep the visual line consistent on exposed runs. As a flatback bevel edge profile, the molding presents a shaped face with a flat mating surface, supporting a clean, defined front while resting securely against the substrate. The 12-foot length lets installers run long sections of edge in one piece, which reduces joints and keeps the pattern flowing along the counter front. As a laminate edge molding from Capital City Counters, it is suited to laminate-based countertop builds where a coordinated decorative edge is needed around the perimeter.
The flatback design on the Capital City Counters edge molding 3692 provides a straight rear surface that aligns against the edge of a countertop or panel. That flat interface simplifies positioning, because the molding meets the substrate along a single plane rather than a complex contour. The bevel on the exposed face shapes the front profile for a defined visual break from the laminate deck, which can help hide slight transitions at the top edge. With its 12-foot Labrador Granite Etchings run, the piece can span many standard counter lengths in one section, so alignment is focused mainly at corners or end cuts rather than mid-run joints.
The Capital City Counters edge molding 3692, in the Labrador Granite Etchings pattern, is intended for countertop or similar work surface edges built with matching laminate decor. By using this specific pattern on the molding, the finished front edge can visually coordinate with Labrador Granite Etchings laminate sheets used on the deck. That pattern continuity supports applications like kitchen counters, shop tops, or utility surfaces where the visual field carries across the horizontal and vertical faces. As a decorative edge molding, it focuses on the exposed perimeter rather than concealed structural areas, positioning it for front edges, outer corners, and visible side runs. The 12-foot length lets installers handle long stretches, such as island fronts or extended walls, in single pieces that carry the Labrador Granite Etchings pattern unbroken across the face.
The flatback bevel edge design of the N/S-3692 flatback bevel edge molding combines a simple mounting surface with a shaped face, which supports a repeatable fit along straight substrate edges. The flatback allows the molding to reference off the face of the countertop build-up consistently, so cut pieces can follow the same alignment strategy around a room. The bevel on the visible side sets a defined front profile, helping installers establish a crisp line that separates the horizontal laminate from the vertical edge. As a laminate edge molding, it is suited to laminate fabrication workflows where pieces are cut from the 12-foot length, fitted to the edge, and aligned so the Labrador Granite Etchings pattern tracks cleanly. The manufacturer part number 3692E identifies this exact flatback bevel configuration and decor, which helps fabricators reorder the same molding when repeating a job or extending an existing counter run with matching edge detail.
Capital City Counters edge molding 3692E is a laminate edge molding classified as decorative edge molding, so it is intended to finish and protect visible laminate countertop or work surface edges.
The molding uses the Labrador Granite Etchings pattern, allowing the visible edge to coordinate with laminate surfaces in the same decor on the countertop deck.
The Capital City Counters edge molding 3692 is 12 feet long, which supports long countertop runs with fewer joints along the exposed front edge.
Flatback bevel edge means the rear of the molding is flat against the substrate while the front face is beveled, helping alignment while providing a shaped visible profile.
This Labrador Granite Etchings edge molding is used on exposed edges of laminate countertops or similar work surfaces where a coordinated decorative front edge is desired.
Manufacturer part number 3692E identifies this specific Capital City Counters flatback bevel edge laminate molding in the Labrador Granite Etchings pattern and 12-foot length.
The Capital City Counters edge molding 3692, Labrador Granite Etchings 12-foot length, offers a flatback bevel laminate edge that coordinates with Labrador Granite Etchings surfaces along countertop fronts. For laminate-based projects that call for a decorative, patterned front edge, this 3692E molding provides the identified profile and decor needed to carry that look around visible perimeter runs.
Sold In: 1 Each