POLISHED ALUMINUM DIVIDER-803P is a New York Metal divider bar mirror molding designed for jobs where a corner or seam needs to be concealed, so installers get a clean visual break between panels without relying on surface fillers. This polished aluminum molding is used in the glass industry, which means it is suited to mirror and glass edge transitions where appearance at the joint matters. The piece is described as a divider bar mirror molding, so it is intended to sit between adjacent surfaces and visually separate or cap them. The profile provides a defined metal edge at the joint, which helps create a straight reference line along long seams. Because the molding is polished, it presents a reflective finish at the exposed face, matching typical mirror trim aesthetics in glass work.
This polished aluminum mirror molding uses its 1-3/8 inch A dimension to span the joint, so installers can position the bar to fully cover the seam while keeping the visible B dimension at 3/8 inch on the face side. The 1/16 inch C dimension creates a thin engagement point at the joint, letting the molding nest closely to the adjoining materials so the trim masks the gap rather than standing proud. As a metal edge molding, it establishes a defined metal boundary where two surfaces meet, which helps when aligning mirrors, panels, or glass sections to a common straight line along the length of the divider.
This New York Metal polished aluminum divider bar mirror molding is used in the glass industry, so it suits mirror installations and similar glass projects where corners or seams are exposed. The divider format lets installers run the molding along the joint between two mirror pieces or between mirror and an adjacent panel, providing a consistent transition strip. With A at 1-3/8 inch, the molding can bridge small gaps while still giving enough coverage on each side of the joint, helping keep the actual seam out of sight. The B dimension of 3/8 inch defines how much metal shows on the face, which helps when coordinating the trim line with surrounding reveals or existing metal frames. Because it is classified as metal edge molding, it is appropriate for edges where a visible metal border is part of the design, such as vertical joints between mirror panels or perimeter seams around glass-clad sections.
The polished aluminum finish on this divider bar mirror molding provides a reflective surface at the exposed face, so it visually aligns with typical mirror trims used in glass work and reduces contrast at the edges. The 3/8 inch B face gives a narrow band of metal, which helps define the joint without overwhelming the surrounding mirror area. The slim 1/16 inch C engagement allows the profile to sit close to the materials at the seam, helping keep the transition tight so light does not catch a deep recess at the joint. As a metal edge molding, it contributes rigidity along the seam line, which can help maintain straightness over longer runs when mirrors or panels are aligned to its edge. The divider bar mirror molding designation means it is purpose-built to conceal corners or seams, supporting repeatable results when multiple joints must present the same finished look across a project.
POLISHED ALUMINUM DIVIDER-803P is a New York Metal divider bar mirror molding, so it functions as a metal edge molding that covers and trims corners or seams between adjacent surfaces.
This divider bar mirror molding is used in the glass industry to conceal a corner or seam, so it creates a finished metal transition where mirrors or glass panels meet.
The 1-3/8 inch A dimension describes the overall reach of the molding, helping determine how far it extends across the joint and how much coverage it provides on each side.
The 3/8 inch B dimension defines the visible face width of the molding, which affects how much metal edge is seen next to the mirror or panel in the finished installation.
The 1/16 inch C dimension describes a slim engagement area at the joint, allowing the molding to sit tightly at the seam so the trim hides the gap without adding bulk.
The polished aluminum finish gives the molding a reflective appearance, helping it visually coordinate with mirror surfaces and other polished trims in glass installations.
This New York Metal polished aluminum divider bar mirror molding brings defined dimensions of 1-3/8 inch A, 3/8 inch B, and 1/16 inch C to seam and corner work, so installers can plan coverage and appearance precisely. Its role as metal edge molding for the glass industry supports mirror and glass joints where a polished metal transition is part of the finish. For projects needing a consistent divider that conceals corners or seams with a polished aluminum face, POLISHED ALUMINUM DIVIDER-803P provides a clearly specified profile to match that requirement.
Sold In: 1 Each