Wurth #6 x 3/4 Inch Screw For Hinge And Slide
Wurth #6 x 3/4 inch screw is a flat head hinge and drawer slide installation screw that joins hardware to wood or similar materials in a compact length. The flat head design seats flush in countersunk hinge and slide holes, which helps hardware sit tight against the mounting surface. The Type 17 auger point starts into material aggressively, so the screw penetrates with less initial resistance in many woodworking situations. The coarse thread runs quickly through material, which helps pull hinges and slides firmly into place. The zinc finish provides a protective metallic coating on the screw surface, which supports normal interior-use environments where these fasteners are commonly installed. A #2 Phillips drive interface matches #2 Phillips drive bits, giving installers a very common drive style to work with on site. Case hardened construction creates a hardened outer layer on the screw, which supports typical driving torque during hinge and drawer slide installation work.
Key Fastener Details For Practical Hinge Work
- The #6 screw size gives a moderate shank diameter, which suits many hinge and drawer slide hole patterns without overwhelming smaller hardware.
- The 3/4 inch length limits penetration depth, which helps when fastening into cabinet parts where only shallow material thickness is available.
- The flat head profile nests into countersunk hardware holes, so hinge leaves and slide flanges sit level against the cabinet surface after tightening.
- The coarse thread design advances rapidly through material, which reduces drive time when installing multiple hinges or drawer slides on a run of cabinets.
- The Type 17 auger point shape aids starting into material, which can reduce wandering at the start of the drive and help keep hinge alignment on layout marks.
- The zinc finish places a plated barrier on the screw, which supports appearance and surface protection in typical interior cabinet environments.
- The #2 Phillips drive works with standard #2 Phillips drive bits, so installers can use common drivers across many cabinet hardware tasks.
- Case hardened construction produces a hardened outer layer on the screw, which supports routine driving loads during hinge and drawer slide installation.
Installation Characteristics That Affect Fit And Drive
The flat head hinge installation screw style is built so the head sinks into matching countersinks, helping hinges and slides fit closely to cabinet faces and sides. The #6 diameter balances grip and hole fit, providing a shank size that matches many hinge and drawer slide mounting holes used in cabinetry. The 3/4 inch length is suited to fastening hardware where the material thickness behind the hinge leaf or slide flange is limited, helping keep penetration inside common cabinet stock. The Type 17 auger point works to create its own entry path into material, which supports starting the screw in many woodworking substrates without extensive pre-drilling. Coarse threads move the screw forward quickly under drive torque, pulling hardware snug to the mounting surface as the head seats. The #2 Phillips drive interface pairs with widely used #2 Phillips drive bits, keeping driver bit changes minimal during hinge and drawer slide installation runs.
Using This Screw In Cabinet And Drawer Projects
Where This Hinge And Slide Screw Is Commonly Applied
This drawer slide installation screw is intended for fastening hinges and drawer slides to cabinet components where a #6 diameter and 3/4 inch length are appropriate. The combination of flat head and coarse thread suits mounting to wood-based cabinet parts that accept countersunk hardware. The Type 17 auger point works when starting screws into many wood substrates often found in cabinetry, helping create a path into the material as the screw is driven. The zinc finish supports use in typical interior cabinet applications where a metallic plated surface is suitable. Case hardened construction aligns with hinge and drawer slide mounting tasks that expect the screw to withstand normal driving torque in shop or jobsite settings.
Details That Support Consistent Mounting And Alignment
The flat head hinge installation screw profile allows the head to seat down into hinge and drawer slide countersinks, which helps maintain consistent hardware position against the cabinet face or side. The #6 screw diameter provides material engagement that balances holding strength with fit through many standard hinge and slide holes, supporting repeatable mounting across a project. The 3/4 inch length works within common cabinet material thicknesses, which helps avoid excessive penetration while still drawing the hardware firmly to the substrate. Coarse threads advance with fewer turns under drive, which supports efficient work when repeating the same hinge or slide layout on multiple doors and drawers. The Type 17 auger point helps the screw establish its driving path as it enters, which supports starting close to layout marks for hinge and slide positioning. The #2 Phillips drive head matches widely used bits, allowing a single bit style to serve many fasteners throughout hinge and drawer slide installation work.
Common Questions About This Wurth Installation Screw
What hardware is this Wurth #6 x 3/4 inch screw intended to fasten?
This Wurth #6 x 3/4 inch screw is described as a flat head hinge and drawer slide installation screw, so it is used to mount hinges and drawer slides to suitable cabinet materials.
How does the Type 17 auger point help during installation?
The Type 17 auger point on this screw is shaped to start into material as it turns, which helps penetration begin with less initial resistance in many woodworking applications.
Why choose a coarse thread zinc screw for cabinet work?
This coarse thread zinc screw advances quickly through material for faster fastening, while the zinc finish provides a plated surface suitable for typical interior cabinet environments.
What driver bit matches this Phillips drive hinge screw?
This Phillips drive hinge screw uses #2 Phillips drive bits, so standard #2 Phillips driver bits interface with the screw head during hinge and drawer slide installation.
How does the 3/4 inch length affect cabinet and drawer installations?
The 3/4 inch length keeps penetration within common cabinet stock thickness while still letting the screw draw hinges and drawer slides tightly against the mounting surface.
What is the benefit of this screw being case hardened?
This screw is case hardened, giving it a hardened outer layer that supports typical driving torque during hinge and drawer slide installation tasks in shop or field work.
Selecting This Screw For Hinge And Slide Mounting
This flat head hinge and drawer slide installation screw from Wurth Baer Supply combines a #6 diameter, 3/4 inch length, coarse threads, and a Type 17 auger point in a zinc, case hardened fastener. Those characteristics work together to fasten hinges and drawer slides to cabinet components in many interior woodworking situations. When a cabinet or drawer project calls for a #6 x 3/4 inch flat head screw with #2 Phillips drive, coarse thread, Type 17 auger point, zinc finish, and case hardened construction, this Wurth screw provides that specific combination for consistent hinge and drawer slide mounting.
