DH Casters Swivel Caster With 3" Rubber Wheel With Brake, Threaded Stem Mount 100lb Capacity - C-LI30T6MSB

DH Casters Swivel Caster For Light Duty Use

DH Casters swivel caster is a threaded stem mount caster built for light duty institutional and industrial applications, so it suits carts, stands, and shop fixtures that stay within a 100 lb load rating per caster. The 3 inch wheel diameter gives a compact profile that still rolls smoothly over typical shop and facility floors, which helps when equipment must move in tight spaces. A 1 inch tread width concentrates the load in a controlled contact patch, supporting predictable rolling on hard surfaces. The gray rubber wheel material is identified as non-marking, so it resists leaving dark streaks on finished or painted floors. A swivel type construction lets the caster rotate for steering, helping operators reposition equipment without dragging. Zinc plating on the caster components provides corrosion resistance, supporting consistent function in normal woodworking and industrial environments where moisture or cleaners may be present.

Key Caster Details That Support Daily Use

• The threaded stem mount comes in a 1/2"-13 x 5/8" thread size, giving a defined interface that ties securely into tapped plates or receivers on carts and fixtures, which supports stable mounting alignment during use.
• The caster load capacity is rated at 100 lb, so installers can plan layouts by multiplying that rating by the number of casters to match expected equipment weights, supporting predictable performance under light duty loads.
• The non-marking gray rubber wheel material is designed to avoid floor marking, which is useful in institutional corridors and industrial areas where appearance and reduced cleanup of streaks or scuffs matter.
• The swivel type configuration allows the caster to rotate as equipment moves, which helps operators maneuver carts into position in restricted aisles or around machinery without excessive effort or unwanted scraping.
• Zinc plating provides corrosion resistance on the metal components, so the caster is suited to environments where exposure to humidity or occasional cleaning solutions would otherwise promote rust and affect smooth movement.

Threaded Stem Mount And Wheel Fit Details

This threaded stem mount caster uses a 1/2"-13 x 5/8" stem, so it interfaces with matching threaded sockets or tapped structures on equipment frames, establishing a positive mechanical connection that resists wobble in service. The 3 inch wheel diameter and 1 inch tread width define the rolling geometry, which affects how the caster handles floor transitions and how high the equipment deck sits above the floor. The nut and bolt wheel assembly secures the gray rubber wheel within the fork, maintaining alignment for smooth rolling while allowing service access when needed. A full double ball swivel raceway supports the swiveling motion, distributing loads through the swivel interface so turning effort stays manageable under the rated 100 lb load.

Using This Threaded Stem Swivel Caster In Practice

Where Threaded Stem Mount Casters Work Best

This DH Casters threaded stem mount unit fits applications where the equipment frame already provides a 1/2"-13 threaded point, such as light duty institutional carts or industrial stands with pre-threaded sockets. In those settings, the threaded stem combines with the swivel type design to let operators spin and roll assemblies through narrow aisles or around obstacles, since the caster can pivot freely under the load. The 3 inch gray rubber wheel is suited to typical hard facility floors, where the non-marking formulation helps preserve tile or coated concrete appearance over time. With a 1 inch tread width, the wheel tracks cleanly without spreading the contact area excessively, which is useful when moving equipment over smooth interior surfaces that benefit from consistent contact pressure.

Why These Caster Details Support Consistent Results

The defined 1/2"-13 x 5/8" threaded stem size means installers can match this caster to properly tapped mounts, which promotes repeatable replacement when swapping units during maintenance. The 100 lb load capacity gives a clear planning number for arranging multiple casters under a cart or fixture, helping maintain performance within the light duty institutional and industrial range described in the product data. The nut and bolt wheel assembly, combined with the full double ball swivel raceway, keeps the wheel and swivel components held in a stable path so rolling and turning stay smooth as equipment is moved. Zinc plating on the metal parts adds corrosion resistance, supporting long-term swivel and rolling function when the caster is used in shops or facilities where moisture or cleaning routines are part of everyday workflow.

Common Questions About This DH Casters Model

Selecting This Caster For Light Duty Mobility

The DH Casters swivel caster with 3 inch gray rubber wheel, threaded stem mount, and 100 lb capacity provides a defined solution for light duty institutional and industrial rolling needs. The non-marking wheel material, zinc-plated components, and full double ball swivel raceway are detailed in the product data, so tradespeople can match this model to applications that value maneuverability, floor appearance, and steady swivel performance. For carts, stands, or fixtures built around a 1/2"-13 x 5/8" threaded stem connection, this caster offers a clearly specified option for planning layouts and standardizing future replacements.