CAT Pack CPR Complaint Spray Gun Kit CPR

CAT Pack CPR Complaint Spray Gun Kit For Pro Finishing

CAT Pack CPR Complaint Spray Gun Kit combines the transfer efficiency of HVLP with the speed and finish quality of conventional air spray, so cabinet and wood finishing jobs move faster without giving up fine atomization. All fluid passages are stainless steel, which resists corrosion from waterborne or solvent-based materials and helps maintain consistent flow over time. Needle and nozzle setups at 0.8 mm, 1.3 mm, and 1.7 mm cover thin stains through heavier coatings, letting one gun handle varied finishing schedules. Air caps CPR2101 at 11 cfm and HVLP1301 at 13.5 cfm at 29 psi match common shop air systems, so air demand stays predictable around other tools. A recommended inlet pressure of 29 psi keeps settings straightforward, helping repeat results when switching operators or jobs.

Key CPR Compliant Spray Gun Details That Matter

• Combining HVLP transfer efficiency with conventional air spray speed supports productive finishing while helping material land on the workpiece instead of drifting away, which can reduce wasted coatings on larger cabinet or millwork runs.
• Stainless steel fluid passages handle a range of coatings, supporting use with many typical shop finishes while resisting internal pitting, which helps keep flow characteristics more stable between cleanings.
• Needle and nozzle sizes of 0.8 mm, 1.3 mm, and 1.7 mm match thin dyes, general-purpose lacquers, and heavier builds, so technicians can dial in film build and flow by swapping setups instead of changing guns.
• CPR2101 air cap at 11 cfm and HVLP1301 air cap at 13.5 cfm at 29 psi tie airflow needs to specific caps, giving predictable consumption that helps plan compressor loading on multi-station spray lines.
• An air inlet of 1/4 inch NPS and a fluid inlet of 3/8 inch NPS align with common hose and pressure pot connections in finishing shops, helping the gun drop into existing rigs without reconfiguring lines.

Spray Gun Setup, Air Requirements, And Connections

The CPR GUN COMPLIANT KIT runs with a nozzle requiring 11 cfm at 29 psi recommended inlet pressure, which matches many shop compressors so air supply stays steady during continuous spraying. The CPR2101 and HVLP1301 air caps are specified at 11 cfm and 13.5 cfm at 29 psi, respectively, tying fan performance directly to known air volumes for easier setup. An air inlet threaded at 1/4 inch NPS fits standard spray air hoses, while the 3/8 inch NPS fluid inlet connects directly to typical pressure pots or pressure cups, streamlining hook-up. Repair kit CX10-106 is specified for this CPR gun, providing a designated maintenance path when components wear.

Using This C.A. Technologies Spray Gun In Daily Work

Where This CPR Compliant Spray Gun Kit Excels

This C.A. Technologies spray gun sits in the Spray Equipment and Spray Guns category, aligning it with cabinet, woodworking, and similar finishing environments where controlled film build is critical. Its ability to combine HVLP transfer efficiency with conventional air spray speed supports production lines that need fast cycle times while still targeting fine, even coverage. The three needle and nozzle setups - 0.8 mm, 1.3 mm, and 1.7 mm - let finishers move from light stains to heavier topcoats by changing internal parts, so one tool can follow work from sealer coat through build coats. Air caps CPR2101 at 11 cfm and HVLP1301 at 13.5 cfm at 29 psi match different performance needs, so the same gun can be configured for tighter work or broader coverage on larger panels.

Details That Support Repeatable Spray Results

All fluid passages being stainless steel gives the internal wetted path a stable surface, which supports consistent flow and atomization characteristics as jobs repeat through the week. The specified 29 psi recommended inlet pressure and known nozzle and cap air demands create a baseline, so once a shop dials in fan pattern and material flow, those settings can be recorded and reused. Having 0.8 mm, 1.3 mm, and 1.7 mm setups tied to one CPR gun helps standardize gun handling across different materials, reducing variation when operators switch between products. Matching air inlet and fluid inlet thread sizes to 1/4 inch NPS and 3/8 inch NPS means hose connections stay consistent, which helps keep rigs configured the same way from job to job.

Common Questions About The CPR GUN COMPLIANT KIT

Selecting This CPR Spray Gun Kit For Finishing

The CPR GUN COMPLIANT KIT from C.A. Technologies blends HVLP transfer efficiency with conventional air spray speed, stainless steel fluid passages, three needle and nozzle sizes, and two defined air caps to support cabinet and woodworking finishing workflows. With specified air and fluid inlets, known cfm demands, and a dedicated repair kit, it fits into existing spray setups with clear operating parameters. Add this spray gun kit to standardize application across stains, sealers, and topcoats while using one CPR platform.