Drawer bumper with reference tab almond 3/4 in

Drawer Bumper With Reference Tab For Consistent Stops

drawer bumper with reference tab is a plastic drawer stop designed to mount to the cabinet and contact the drawer front. The bumper is 3/4 inch high, so it presents a defined stop point that keeps drawer travel consistent from opening to opening. The almond color matches typical light cabinet interiors, which helps the installation blend into finished casework. A single #4 x 1/2 inch flat head screw fastens the bumper to the cabinet, giving a rigid mechanical connection that holds position over long-term use. The reference tab on the bumper lines up to the front of the drawer, so the installer can set every bumper to the same datum without measuring each location. This part is manufactured by Bainbridge Manufacturing, giving shops a repeatable part number across jobs.

Practical Drawer Bumper Details That Save Time

• The bumper is made of plastic, which provides a firm but non-metallic contact surface that cushions the drawer front against the cabinet during closing.
• The 3/4 inch height defines how far the drawer front stands off when closed, which standardizes reveal and feel across multiple drawers in the same run.
• The bumper mounts with a single #4 x 1/2 inch flat head screw, so installation is straightforward at each location while maintaining positive retention on the cabinet.
• The screw is inset into the bumper, which keeps the fastener head recessed and improves the finished appearance of the installed bumper at the cabinet front.
• The almond color finish coordinates with many light-colored cabinet interiors, so the bumper does its job without drawing attention on completed installations.
• The reference tab built into the bumper gives a physical alignment point to the drawer front, speeding up layout when repeating the same position on multiple drawers.

Mounting And Alignment Details For This Drawer Bumper

This Bainbridge Manufacturing drawer bumper mounts to the cabinet using a single #4 x 1/2 inch flat head screw, so the installer only needs one hole per location to secure it. Because the screw is inset, the head sits below the contact face, allowing the drawer front to bear only on the plastic surface. The 3/4 inch high bumper body establishes the stop position, so once the reference tab is set to the drawer front, the depth is inherently controlled. The almond plastic body and integrated tab give a single molded piece to position and fasten, which keeps the mounting workflow direct on both new cabinet builds and retrofit work.

Using Drawer Bumpers With Tabs In Cabinet Work

Where This Almond Drawer Bumper Fits Best

This drawer bumper with reference tab is intended for cabinet installations where a plastic stop is needed between cabinet structure and drawer front. The part is 3/4 inch high, so it suits applications where that stand-off height creates the desired closed position relative to the cabinet face. Because it attaches with a single #4 x 1/2 inch flat head screw, it works anywhere a pilot hole for that screw size can be driven in cabinet material. The almond finish coordinates with typical light interior finishes, so it is suited to residential and commercial casework that uses similar tones. By lining the reference tab to the drawer front, installers can repeat the same stop point row after row in drawer banks.

Why The Reference Tab And Screw Mount Matter

The integrated reference tab on this Bainbridge Manufacturing drawer bumper gives a physical edge to register against the drawer front, so alignment is set by contact rather than by tape measure layout. That minimizes layout time on multi-drawer installations and keeps reveals consistent from top to bottom. The single #4 x 1/2 inch flat head screw creates a fixed mounting point, which keeps the bumper from drifting over repeated drawer use. With the screw head inset, only the plastic face touches the drawer front, protecting the drawer surface from metal contact. The 3/4 inch bumper height means once the tab is positioned, the stop depth is established without secondary adjustment steps, simplifying repeatable cabinet shop processes and field work. The plastic construction also provides a defined impact surface that works repeatedly as drawers open and close in normal use.

Common Questions About This Drawer Bumper With Tab

Select This Drawer Bumper For Consistent Drawer Stops

The Bainbridge Manufacturing drawer bumper with reference tab in almond provides a 3/4 inch high plastic stop that mounts with a single #4 x 1/2 inch flat head screw. The inset screw and molded reference tab give a clean contact surface and repeatable alignment to the drawer front. For cabinet work that needs consistent stop depth and a light interior color match, this bumper offers a defined part number and straightforward screw-mounted installation ready to integrate into drawer production or field projects.