Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Traditional Advantage Three knob gives cabinet and furniture doors a defined 1-1/4 inch diameter grip point in a compact round profile, so hands land consistently on center when pulling doors or drawers in everyday use. The Verona Bronze finish establishes a dark, warm tone across the knob surface, which helps visually ground lighter cabinet finishes while keeping a traditional look. Material is zinc die cast, providing a solid, uniform casting that supports repeatable alignment across multiple doors in the same run. Projection of 1 inch sets the hand clearance off the face of the door, helping fingers curl behind the knob without feeling crowded. A base diameter of 7/16 inch creates a clear bearing surface against the cabinet face, which helps define a stable contact area when tightening the knob down. The knob width of 1-1/4 inch matches the stated diameter, keeping sizing straightforward during layout.
This Berenson cabinet knob uses its 1-1/4 inch diameter and matching 1-1/4 inch overall width to keep sizing easy to read off drawings or cut sheets when specifying quantities. The 1 inch projection sets a predictable offset from the cabinet face, which helps keep knob faces aligned in a straight visual plane when mixed with other 1 inch projection hardware. The 7/16 inch base diameter marks a compact footprint on the door or drawer front, useful when working near narrow frame rails or stile edges. With a Verona Bronze finish over zinc die cast material, the knob presents a uniform appearance across a full kitchen or project, supporting consistent visual alignment when installed in repeating rows.
The Berenson Traditional Advantage Three knob with 1-1/4 inch diameter works well on cabinet doors and drawers where a round pull point is preferred, because the head size sits comfortably on standard face frame and frameless fronts. The 1 inch projection keeps the grip zone close to the door surface, which suits installations where hardware cannot extend too far into walkways or tight clearances. Verona Bronze finish pairs with traditional and transitional cabinet styles, so the knob can be specified across kitchens, baths, or built-ins that share this finish tone. The zinc die cast construction supports uniform mass from piece to piece, which is helpful when a project calls for many identical knobs laid out in symmetrical banks.
The defined 1-1/4 inch diameter on this 9380-10VB-P Berenson knob lets installers lay out drilling points using a consistent centerline from the door edge, which reduces variations from one door to the next. The 1 inch projection dimension creates a repeatable offset from the cabinet surface, so knob faces line up evenly when viewed from the side on long runs of cabinetry. A 7/16 inch base diameter concentrates the contact area, which helps the knob sit flush against flat fronts and maintain its orientation after tightening. Because the knob width equals the listed diameter, millworkers can read that single measurement and understand both face size and overall span, simplifying specification work. The Verona Bronze finish on zinc die cast material keeps a consistent color reference, which supports clean visual alignment when knobs are installed in sets across upper and lower cabinets.
The Berenson Traditional Advantage Three knob has a 1-1/4 inch diameter and width, a 1 inch projection, and a 7/16 inch base diameter, giving clear sizing for layout on cabinet doors and drawers.
The 9380-10VB-P Berenson knob is made from zinc die cast, which provides a solid, uniform casting that helps it seat evenly against cabinet faces in typical installations.
This Berenson Traditional Advantage Three knob has a Verona Bronze finish, giving it a dark, warm tone that coordinates with traditional cabinet styles using similar bronze hardware colors.
The Verona Bronze cabinet knob projects 1 inch from the cabinet face, setting a defined clearance for hand grip and helping maintain a low-profile hardware line along cabinetry.
This Berenson cabinet knob has a 7/16 inch base diameter, creating a compact contact area that fits well on standard stile widths and narrow drawer fronts.
This Verona Bronze knob is part of the Advantage Plus collection from Berenson, aligning it with other decorative hardware designed under the same series naming.
The Berenson Traditional Advantage Three knob in Verona Bronze combines a 1-1/4 inch diameter face with a 1 inch projection and a 7/16 inch base, giving clear, repeatable dimensions for cabinet layouts. When a project calls for Verona Bronze hardware built on zinc die cast construction, this 9380-10VB-P knob offers a defined size set that matches drawings and on-site drilling patterns across multiple doors and drawers.
