Berenson Wave Series Polished Chrome 1-1/4" (32 mm) L x 1-1/4" (32 mm) W Knob, - 9322-1026-C

Berenson Wave Series Knob For Cabinet Projects

Berenson Wave Series knob gives you a compact 1-1/4 inch by 1-1/4 inch pull point that works well on cabinet doors or drawers where a consistent look matters. The 1 inch projection sets a stable grip distance from the cabinet face, which helps keep knuckles clear while still staying tight to the surface. Its zinc die cast construction forms a solid, uniform body, supporting repeatable alignment across multiple fronts. The polished chrome finish provides a bright surface that ties in with other polished chrome hardware on the job. A 7/16 inch square base keeps the contact area defined, which is useful when laying out drilling locations on narrow rails or small drawer fronts. The knob design, combined with its square base, supports straight visual lines across a run of cabinetry.

Key Wave Knob Details For Daily Use

• The 1-1/4 inch length or diameter provides a compact pull area that suits smaller cabinet faces, helping maintain proportion on narrow doors and drawers.
• The matching 1-1/4 inch width creates a true square profile, which simplifies layout when spacing multiple knobs across a bank of fronts.
• The 1 inch projection establishes a consistent stand-off from the cabinet surface, giving fingers room to pull while keeping the knob close to the face for a clean line.
• The 7/16 inch square base diameter defines a focused footprint, supporting precise centering over a drilled hole on face frames or panel fronts.
• The zinc die cast material creates a single-piece metal body, supporting consistent sizing and shape from knob to knob across a full installation.
• The polished chrome finish delivers a bright, reflective surface that visually coordinates with other polished chrome decorative hardware on the same project.

Mounting And Fit Details For This Knob

This Wave Series knob uses a 1-1/4 inch square face to seat visually on cabinet fronts, which aids in aligning it with rails, stiles, or drawer edges. The 1 inch projection sets how far the grip sits off the surface, establishing a repeatable clearance dimension from door or drawer faces. With a 7/16 inch square base, the contact area is limited to a compact footprint, which is useful when spacing knobs close to panel edges or decorative profiles. The zinc die cast construction supports uniform threads and body geometry, which helps each knob sit square against the mounting surface so rows of knobs line up consistently.

Where This Berenson Wave Knob Fits Best

Using The Wave Series Knob On Cabinets

The Berenson Wave Series knob, at 1-1/4 inches in both length and width, lends itself to cabinet doors and drawers that call for a small, squared pull point. This square profile helps keep visual alignment straightforward when matching knob centers along upper and lower cabinets. The 1 inch projection sets a defined reach that works well on kitchen, bath, or storage cabinetry where users regularly grab and pull from the front. Its 7/16 inch square base focuses contact near the center, which is useful on narrower frame members or reduced-width drawer fronts. The polished chrome finish supports projects that rely on polished chrome decorative hardware for a uniform appearance across hinges, pulls, and knobs. Because the knob is zinc die cast, it maintains consistent form, so multiple pieces read as a matched set on a full run of cabinetry.

Details That Support Repeatable Results And Layout

The 1-1/4 inch by 1-1/4 inch face dimension gives a clear reference edge-to-edge, which helps when setting up drilling jigs or marking centerlines on repetitive cabinet layouts. Installers can rely on the square geometry to keep the knob aligned with door and drawer edges for straight sight lines. The 1 inch projection defines a standard offset that remains the same across all installed knobs, which matters when doors swing past adjacent surfaces or when drawers pass by neighboring fronts. With a 7/16 inch square base diameter, the bearing surface stays compact, reducing visual interruption on detailed profiles while still covering the mounting bore. The zinc die cast material supports a stable threaded engagement, so the knob can be drawn tight to the surface for a flush, even seating. Together, these details make the Berenson 9322-1026-C knob a predictable choice where consistent layout and alignment are important.

Common Questions About The Berenson Wave Knob

Selecting This Knob For Chrome Cabinet Runs

The Berenson Wave Series knob in polished chrome, with its 1-1/4 inch square face and 1 inch projection, offers a defined pull point for cabinet doors and drawers. At Wurth Baer Supply, this zinc die cast knob supports projects that call for polished chrome decorative hardware with consistent sizing, helping installers maintain alignment and a unified look across full cabinet runs.