Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Wave dull chrome knob uses the Wave Series profile and gives cabinets a square, modern pull point that suits both shop-built and replacement work. The knob is identified as Berenson Corporation part 9323-10DC-C, so it matches project specs that call out this exact number. The zinc die cast material creates a solid-feeling pull point that holds up during everyday use on frequently opened doors or drawers. A dull chrome finish keeps reflection low, which helps the knob blend with other muted decorative hardware in the same run. The knob measures 1-1/4 inch, or 32 mm, in both length and width, so it presents a balanced square face that lays out cleanly on face frames or slab fronts. A square base at 7/16 inch steps down the footprint, helping the knob sit visually lighter while still giving a defined contact area against the surface.
The 1-1/4 inch width and length give the Berenson Wave Series knob a true square footprint, which simplifies setting hardware lines when measuring from door edges or stiles. This equal dimension in both directions helps keep rows and columns straight during repetitive layout. The 1 inch projection controls how far the knob stands off the face, which matters when doors open near adjacent walls or appliances where extra projection could cause interference. A 7/16 inch square base means the bearing surface is compact, so the knob lands within common rail and stile widths without crowding panel details. The specified 45mm screw size connects the knob to the cabinet through a standard bore, supporting a typical cabinet construction workflow where pieces share similar thicknesses.
This knob belongs to the Berenson Wave Series, so its 1-1/4 inch square face and matching 1-1/4 inch width tie in with other Wave decorative hardware on doors and drawers. In a run of cabinets, the dull chrome finish supports a unified look when other components call for the same tone. The zinc die cast material suits residential or light commercial cabinetry where hardware experiences frequent but ordinary operation. At 1 inch projection, the knob suits cabinet faces along passages or tight galley layouts, because the pull point stays close to the door while still giving enough clearance for a fingertip or full-hand grip. The 7/16 inch square base centers the load near the bore, which helps the knob sit solidly on both framed and frameless fronts during everyday use.
The Berenson 9323-10DC-C knob uses a 1-1/4 inch by 1-1/4 inch square head, which makes layout straightforward when installers work with story sticks or jigs based on equal offsets from edges. With the square geometry, the knob visually reveals any rotation, encouraging precise alignment across a bank of doors. The 1 inch projection defines a consistent standoff, so doors and drawers open without the pull feeling either too shallow or oversized for the hand. A 7/16 inch square base focuses pressure near the mounting screw, which helps the knob seat flush against the surface once tightened. The specified 45mm screw size ties the knob through the cabinet front, matching common drilling practices and allowing installers to maintain a single bore pattern across the job.
The Berenson Wave knob measures 1-1/4 inch in length and 1-1/4 inch in width, giving it a square profile that helps align hardware consistently on cabinet doors and drawers.
The knob has a 1 inch projection, which sets the grip point off the cabinet face enough for fingers while staying compact in tighter kitchen or bath layouts.
The 9323-10DC-C knob is zinc die cast, providing a dense metal body that supports a sturdy pull point on doors and drawers during regular operation.
This knob uses a dull chrome finish, giving a softer metallic appearance that coordinates with other low-gloss metal components in a hardware layout.
The Berenson Wave knob has a 7/16 inch square base, concentrating contact near the mounting point and helping it seat neatly within common rail and stile widths.
The knob uses a 45mm screw size, matching typical cabinet door and drawer thicknesses so installers can use a standard through-bore mounting approach.
The Berenson Wave Series dull chrome 1-1/4 inch knob ties together zinc die cast construction, a 1 inch projection, and a 7/16 inch square base in one consistent part. With the 9323-10DC-C designation and 45mm screw size, it fits projects where matching hardware, verified dimensions, and straightforward through-bore installation all matter on cabinet runs.
