Infinex Round U-Clip Set of 2

Infinex Round U-Clip Set For LED Extrusions

Infinex Round U-Clip Set of 2 is a Tresco Lighting LED lighting accessory designed for mounting round extrusion using a U-clip and magnet combination. This U-clip set works as a mounting solution for LED extrusion where a compact mechanical hold is needed along the length of the profile. Each set is manufactured under Tresco Lighting branding and identified by manufacturer part L-XRND-UCLP-1, giving installers a clear reference when matching parts across projects or reorders. As part of the LED Lighting Accessories category, this set supports Tresco LED extrusion layouts in cabinet, display, or architectural runs where a round profile is used and a U-clip style hold-down is preferred for layout consistency.

Practical Details That Support Mounting Work

• One U-Clip/magnet is recommended for every 1' (0.3 m) of extrusion, which helps installers space mounting points evenly along a run for consistent support of the round extrusion.
• The recommendation of one U-Clip/magnet per foot gives a simple layout rule that can be scaled for short or long LED extrusion runs without additional calculation on site.
• No. #4 Phillips flat head screws are specified with each U-Clip set, so the mounting interface is clearly matched to a common screw drive type used in woodworking and cabinet installation environments.
• Each U-Clip uses a magnet with the clip, which provides a defined holding method between the extrusion and the clip position, supporting repeatable placement along the LED fixture.
• The set is part of the LED Lighting Accessories product class, so it is intended to work in conjunction with LED fixtures rather than as a general-purpose fastener, helping installers keep components aligned to lighting layouts.

Mounting Pattern And Screw-Based Installation Use

The U-clip/magnet recommendation of one per 1' (0.3 m) of extrusion defines a repeatable mounting pattern that can be carried across an entire Tresco round extrusion run. Using No. #4 Phillips flat head screws ties the clip directly to a fastening method widely used in woodworking and cabinet trades, so installers can drive the screws with standard Phillips bits while keeping the screw heads flush with the clip recess. Because this part is positioned as an LED lighting accessory, it is applied where an LED extrusion is present, so trades can treat the clip spacing figure as part of the lighting layout rather than a separate structural calculation.

Using The U-Clip Set In LED Installations

Where This Infinex U-Clip Set Is Applied

This Tresco Lighting U-Clip set is specified for round extrusion, so it is used wherever a Tresco round LED extrusion is installed and needs clip-based mounting along its length. The designation as LED Lighting Accessories places it within lighting system layouts, meaning the clips are applied along LED extrusion runs rather than as general hardware. One U-Clip/magnet for every 1' (0.3 m) of extrusion gives a spacing guideline that can be used on undercabinet, display, or linear applications that rely on round extrusion profiles. Because the product name identifies it as an Infinex Round U-Clip Set of 2, it is tied directly to Tresco Infinex round extrusion workflows rather than unrelated mounting tasks.

Why These Mounting Details Support Consistent Results

The stated recommendation of one U-Clip/magnet per foot of extrusion gives installers a predictable support rhythm, helping the round extrusion track stay aligned and supported along its entire length. Using No. #4 Phillips flat head screws means the fastening method is compatible with common driver bits and allows the screw head to sit flush within the clip, which helps the round extrusion seat properly in the U-shaped holder. The presence of both a U-clip and magnet in the recommendation creates a two-part holding strategy, with the clip and magnet working together to keep the LED extrusion in contact at each mounting point. As a defined LED Lighting Accessories component with manufacturer part L-XRND-UCLP-1, this U-clip set can be specified on drawings and material lists so field crews use the same mounting pattern from project to project.

Common Questions About This U-Clip Set

Select This U-Clip Set For Round Extrusions

Choose the Infinex Round U-Clip Set of 2 when a Tresco Lighting LED extrusion run uses a round profile and needs U-clip and magnet mounting points. The one U-Clip/magnet per 1' (0.3 m) recommendation gives a clear rule for spacing along the extrusion. With No. #4 Phillips flat head screws specified for the set, installers can plan on a familiar fastening method. Using this LED Lighting Accessories part under manufacturer number L-XRND-UCLP-1 keeps Tresco-based lighting layouts aligned with the brand-specific mounting approach.