LED 1.5W Warm White Tape Light For Projects

LED 1.5W Warm White Tape Light delivers a 20 foot roll of low heat, 12V tape lighting that suits extended cabinet, display, or shelf runs where consistent warm illumination is needed. The tape operates at 1.5 watts per foot, so power demand stays predictable across longer layouts, which helps when planning transformer sizing and circuit loading. The warm 2700K color temperature keeps light output in a warm white range, supporting residential and commercial millwork where a softer tone is preferred. As part of Tresco Lighting LED tape lighting, this product aligns with typical shop installations that rely on linear lighting rather than point-source fixtures. The tape format lets lighting follow cabinet runs, toe kicks, or signage contours, supporting clean lines without fixture clutter. With an average rated life of 25,000 hours, the tape is designed for long service intervals in everyday use environments.

Key Tape Lighting Details For Daily Work

• The tape is stocked in 20 foot rolls, giving installers a continuous length to work with on extended runs, which reduces splicing and joint points along cabinet or display sections.
• Power consumption is rated at 1.5 watts per foot, allowing load calculations to be done quickly by multiplying the total installed length, which supports proper transformer selection and circuit planning.
• The tape uses a 3M adhesive peel and stick back for easy installation, so it mounts directly to prepared surfaces, saving time compared to mechanical mounting methods.
• The tape can be cut every 3 inches, which lets installers trim runs to closely match cabinet, shelf, or niche dimensions while still staying within the designated cut intervals.
• The tape is designed for a 20 foot maximum length for a continuous run, so installers know the upper limit for a single feed, which helps organize layouts into segments when needed.

Installation And Connection Details For This Tape

The tape uses a 3M adhesive peel and stick back, so it presses into place along cabinet edges, undersides, or channels without separate fasteners, which speeds up installation on finished surfaces. The tape can be cut every 3 inches, providing preset cut points that align with standard cabinet module sizes, so installers can terminate near panel or shelf edges with minimal waste. The 20 foot maximum length for a continuous run establishes how far the tape can be extended from a single power feed, helping layouts stay within the product's designed operating length. The tape can be inserted into straight feed, t-connector, or right-angle connector types, allowing linear, branching, or corner transitions that follow cabinet layouts and room geometry.

Using This Tresco LED Tape In Real Projects

Where This LED 1.5W Warm White Tape Fits

This LED 1.5W Warm White Tape Light, stocked in 20 foot rolls, works well wherever long, uninterrupted linear lighting is needed across cabinets, counters, or casework. The 2700K warm white output supports installations where a softer white is desired, such as residential kitchens or hospitality millwork. Because power use is 1.5 watts per foot, the tape can be applied along multiple cabinet bays while staying within planned electrical loads. The tape's low heat characteristic helps in tight millwork cavities or enclosed runs, reducing thermal impact on adjacent materials. With an average rated life of 25,000 hours, the tape supports applications expecting regular daily use over long periods.

Details That Support Consistent, Repeatable Layouts

The ability to cut the tape every 3 inches gives repeatable, measurable increments that match typical cabinet and shelving spacing, simplifying shop drawings and on-site adjustments. The 20 foot maximum length for a continuous run defines a clear design limit, which helps keep each run within the product's intended operating range and supports consistent brightness along its length. Straight feed, t-connector, and right-angle connector options allow the same tape to handle straight lines, branches, and corners, keeping layouts unified instead of mixing different lighting types. The 3M adhesive peel and stick back provides a uniform mounting method along the entire run, supporting consistent alignment during installation. Tresco fixtures are designed to operate only with genuine Tresco transformers, power cables, connecting cables, and switches, which means using matched components maintains the system design and operating characteristics. It is recommended to use Tresco accessories with Tresco fixtures, so the tape light can function within the manufacturer's intended ecosystem.

Common Questions About This LED Tape Light

Selecting This Tape Light For Your Next Run

This LED 1.5W Warm White Tape Light from Tresco Lighting combines a 20 foot roll, 2700K warm white output, and 1.5 watts per foot in a low heat, 12V system. The tape can be cut every 3 inches and used up to a 20 foot maximum continuous run, supporting precise layouts across cabinets and displays. With 3M adhesive peel and stick backing and connector options for straight, t, and right-angle transitions, it adapts to typical millwork geometries. Use it where a warm linear LED tape lighting solution with defined run limits and long 25,000 hour average rated life is needed.