FlexTape LED 4.4W Daylight Tape Light For Projects

FlexTape LED 4.4W daylight tape light delivers a 156 inch Tresco Lighting LED tape run designed for installations that need a long, consistent daylight strip in a compact format. The tape operates at 4.4 Watts per foot, so each run provides strong LED output while leaving clear expectations for load per foot when sizing transformers in a layout. This model is stocked in 13 foot rolls, giving installers a predictable length for planning cabinet, shelving, or task-lighting runs where repeated sections are required. The tape is classified as LED tape lighting, so it fits into typical linear lighting layouts where low-profile, flexible strips are preferred over rigid bars. The system runs on 12V, which keeps it aligned with common low-voltage lighting setups in woodworking and cabinet shops.

Daylight LED Tape Details That Support Jobs

• This FlexTape LED 4.4W daylight tape light is stocked in 13 foot rolls, so runs can be planned around a known length when laying out multiple cabinet sections or long counters without guesswork.
• The tape uses 4.4 Watts per foot, which lets you calculate total load over a run and match it to appropriate Tresco transformers for predictable electrical performance.
• A 3M adhesive peel and stick back provides direct bonding to clean mounting surfaces, reducing mechanical mounting steps and helping speed through repetitive linear installs.
• The tape can be cut every 3 inches, so lengths can be trimmed closely to cabinet, shelf, or cove dimensions while keeping within the designed cut points for proper operation.
• A 20 foot maximum length for a continuous run defines how far you can extend connected sections before starting a new run, protecting light output consistency along the layout.
• The tape is described as low heat, which supports use in tight woodworking spaces where limiting temperature near wood, finishes, or stored materials is important.

Installation Details For LED Tape Mounting

This FlexTape LED 4.4W daylight tape light uses a 3M adhesive peel and stick back, so installation relies on direct adhesion of the tape to the chosen surface rather than brackets. The ability to cut the tape every 3 inches lets you size segments precisely to match cabinet bays, shelves, or other features without large dead zones at the ends. The 20 foot maximum length for a continuous run sets the boundary for how many connected sections can share the same feed while keeping performance within the designed range. The tape connects using straight feed, T-connector, or right-angle connector options, so layouts can turn corners or branch where needed while maintaining electrical continuity.

How This FlexTape LED Works In Real Projects

Where This FlexTape LED Daylight Tape Fits

This FlexTape LED 4.4W daylight tape light is part of the LED tape lighting category, so it is suited to installations where a slim, flexible strip is preferred over bulkier fixtures. The 156 inch roll length supports long, continuous undercabinet or display runs where a single tape segment can cover multiple cabinets or a full case section. Because the tape operates at 12V, it aligns with common low-voltage lighting infrastructures used in woodworking and commercial millwork environments. The ability to cut every 3 inches lets you tailor segments for shorter cabinets or niche spaces while still basing each piece on the same Tresco Lighting part number L-FLXTPE-DRV-1. Straight feed, T-connector, and right-angle connector options mean the same tape can handle linear runs, branching sections, and 90 degree turns across a project.

Details That Support Consistent Lighting Results

The tape is rated at 4.4 Watts per foot, which gives a clear power figure when planning multi-run installations and balancing total wattage across several transformers. A 20 foot maximum length for a continuous run defines how far you can extend linked sections from one feed, supporting consistent performance at the far end of the tape. The daylight 6500K description identifies the color characteristics of the light, which helps keep visual consistency across adjacent work areas, displays, or cabinet banks that share the same product. The average rated life of 25,000 hours indicates long service intervals in normal operating conditions, which is important when tape is mounted in finished millwork where access after installation can be limited. The low heat statement supports use near wood and laminates, since the LED tape contributes less thermal load to enclosed or tight spaces. The note that Tresco fixtures are designed to operate only with genuine Tresco transformers, power cables, connecting cables, and switches shows that this tape is engineered as part of a coordinated system that is intended to work together electrically.

Common Questions About This FlexTape LED Tape

Choose This FlexTape LED For Planned Runs

The FlexTape LED 4.4W daylight tape light from Tresco Lighting combines a 13 foot roll length, 4.4 Watts per foot, and 12V operation, making it well suited to structured low-voltage layouts. With cut points every 3 inches, a 20 foot maximum continuous run, and a 6500K daylight appearance, it supports predictable planning across cabinets, shelves, or displays using a single LED tape family.