KA 65 Plane Router Bit for Conturo Edge Banding is a Festool router bit designed for use with the Festool MFK 700 Trim Router, so it directly supports the edge banding workflow built around that specific machine. The bit removes excess edge banding material, which means you can bring banded edges down flush to the workpiece rather than leaving a proud lip. That action helps produce clean transitions between banding and core material on cabinets, furniture parts, or similar components. Because it is made for both flat and beveled pieces, the same bit handles square edges and angled details in one system, which simplifies tool selection on the bench. The Festool identity and manufacturer part number 500368 give installers and shops a clear match when standardizing tooling across multiple routers and workstations.
This router bit is specified for use with the Festool MFK 700 Trim Router, so installation follows the same collet and setup routine used for other bits on that machine. Because the bit is matched to the MFK 700, its geometry works with the trim router base system that guides flush trimming along edge banding. Using one dedicated bit for removing excess banding on flat and beveled pieces keeps setup changes around the router focused on base position and reference surfaces instead of changing cutters. The Festool designation on the KA 65 Plane Router Bit for Conturo Edge Banding also helps crews keep it assigned to the MFK 700 station in the shop or on site.
The KA 65 Plane Router Bit for Conturo Edge Banding is for use with the Festool MFK 700 Trim Router, placing it directly in workflows that rely on that trim router for laminate or edge banding work. When excess banding material stands proud of the panel, this bit removes that overhang so edges move from rough-banded to flush-trimmed in one pass guided by the MFK 700 base. On flat pieces, the bit supports edging of cabinet sides, doors, and shelves where a straight edge is required. On beveled pieces, it handles edges that meet at an angle, so banded miters or sloped components can be trimmed without changing to a different cutter. Because it is a Festool router bit identified by part number 500368, shops using Festool tools can match their trim stations and replacement stock around the same cutter.
Since the router bit is designed specifically for the Festool MFK 700 Trim Router, its fit to that platform supports repeatable work along the length of an edge band. The bit removes excess edge banding material rather than just easing the edge, so it brings the banding and core material to the same plane and reduces the need for follow-up leveling. On flat pieces, the flush trimming capability lets fabricators move directly from banding application to final sizing passes on straight runs, which helps maintain even reveal lines along cabinet fronts. On beveled pieces, the same flush trimming behavior at an angle allows miters and non-square edges to carry the banding cleanly through the corner, keeping profiles consistent around the workpiece. The clear Festool and KA 65 Plane Router Bit naming, along with the 500368 number, gives purchasing teams and installers a precise way to call out this specific cutter when aligning MFK 700 router setups.
The KA 65 Plane Router Bit for Conturo Edge Banding is for use with the Festool MFK 700 Trim Router, so it is matched to that router platform for edge banding tasks.
The Festool router bit with part number 500368 removes excess edge banding material, bringing the banding flush with the workpiece for a smoother transition along the edge.
The router bit supports flush trimming on beveled pieces, so angled or mitered edges with banding can be trimmed to follow the bevel accurately.
This Festool KA 65 Plane Router Bit is designed for flush trimming on flat pieces, which fits typical banded cabinet sides, doors, and shelves.
The KA 65 Plane Router Bit for Conturo Edge Banding integrates with the Festool MFK 700 Trim Router, placing it within Festool edge banding workflows using that trim router.
The KA 65 Plane Router Bit for Conturo Edge Banding name identifies it as a Festool router bit intended to plane down edge banding material for flush trimming operations.
The KA 65 Plane Router Bit for Conturo Edge Banding is a Festool router bit specified for the Festool MFK 700 Trim Router, so it aligns directly with that trim router in edge banding setups. By removing excess edge banding material on flat and beveled pieces, the bit moves parts from freshly banded to flush-trimmed using the same router. With the Festool designation and manufacturer part number 500368, ordering this specific cutter through Wurth Baer Supply keeps MFK 700 edge banding stations using a known, matched router bit.
Sold In: 1 Each