Knape and Vogt SBM 11-3/8" White Bottom Mount Waste Pullout with 1-50 Quart White Bin Standard, SBM12-1-50WH

Knape And Vogt Bottom Mount Waste Pullout Use

Knape and Vogt bottom mount waste pullout SBM12-1-50WH provides a single 50 quart white bin on a bottom mount pull-out frame, so you can dedicate a cabinet bay to contained trash collection without sacrificing interior organization. The unit sits on heavy-duty ball bearing precision slides, allowing the bin to travel smoothly in and out of the cabinet, which supports consistent operation under everyday kitchen or bath use. A white bin and white bottom mount frame create a unified look inside light-toned cabinets, helping maintain a clean visual line when the pull-out is open. As a bottom mount trash pullout, the hardware carries the load at the cabinet floor, which is useful when side walls are obstructed or already occupied by other hardware. The design serves as a standard waste solution in kitchen and bath cabinets where a single, large-capacity bin is preferred.

Key Details That Support Daily Cabinet Use

• KV heavy-duty ball bearing precision slides support the 50 quart bin during travel, so the pull-out opens and closes smoothly and consistently under typical trash loads.
• An updated wire management system holds bins securely in place, which keeps the 50 quart bin from shifting during use and helps the rim stay aligned with the frame.
• Pre-assembled units reduce on-site setup because the pull-out arrives assembled, letting installers focus on positioning and fastening instead of building subcomponents.
• Heavy-duty mounting straps tie the frame into the cabinet, which creates a solid connection at the bottom so the pull-out tracks accurately over repeated cycles.
• Installation uses only 4 screws, simplifying layout inside the cabinet and streamlining labor when multiple units are being installed on the same project.

Bottom Mount Trash Pullout Installation Workflow

This bottom mount trash pullout is pre-assembled and uses heavy-duty mounting straps, so the frame positions as a single unit on the cabinet floor, which simplifies alignment for the 50 quart white bin. Because installation requires only 4 screws, the fastening pattern stays straightforward and repeatable from cabinet to cabinet, which is useful on multi-unit jobs. The heavy-duty ball bearing precision slides are already integrated into the pull-out, eliminating separate slide mounting and helping the bin track true once the frame is secured. The updated wire management system is built into the frame to engage the bin, so once the unit is fastened, the bin seats into the holder and remains captured during normal operation.

Trash Pullout Details For Real-World Cabinet Projects

Single Bin Bottom Mount Layout In Cabinets

This single bin waste pullout uses a 50 quart white bin on a bottom mount frame, so one cabinet opening can handle a substantial trash volume while leaving the upper cabinet area visually clean. The category listing as a bottom mount trash pullout defines how it occupies the cabinet floor, which matters when planning around plumbing, sink bases, or existing side hardware. Behind the single bin there is storage space for trash bags or cleaning products, letting installers allocate one cabinet for both waste and related supplies without separate shelving. The bin is secured by the updated wire management system, so when the pull-out travels on its heavy-duty ball bearing precision slides, the bin follows the frame rather than drifting, which helps maintain clearance to face frames and doors.

Features That Support Repeatable Slide Performance

The KV heavy-duty ball bearing precision slides are built into this SBM12-1-50WH unit, so every installation starts from the same factory-aligned slide geometry, which supports predictable motion from job to job. Heavy-duty mounting straps connect the pull-out frame to the cabinet, so once fastened with 4 screws, the slide rails have a stable base that resists racking in normal use. The updated wire management system holds the 50 quart bin to the frame, which keeps weight centered over the slides and supports smoother travel. A clip-on handle is supplied on all single bin units, giving the user a consistent grab point at the front of the pull-out so opening forces are applied where the slides and frame are designed to carry them. An optional door-mount bracket is available for projects that need the cabinet door attached directly to the pull-out frame, allowing the same hardware to support either independent-front or door-attached configurations. Optional lids are available for this bin, which allows projects to add a covered waste compartment while retaining the same bottom mount pull-out platform.

Common Questions About This Trash Pullout

Selecting This Bottom Mount Pullout For Your Project

This Knape and Vogt bottom mount waste pullout combines a 50 quart white bin, heavy-duty ball bearing precision slides, and a pre-assembled frame that installs with only 4 screws, making it suited to kitchen or bath cabinets where a single large-capacity waste station is required. The updated wire management system, clip-on handle, and storage space behind the bin support straightforward daily use once mounted. When a project calls for a standard single-bin pull-out with the option to add door mounting or lids, this SBM12-1-50WH configuration offers a defined, repeatable hardware solution you can specify cabinet after cabinet.