Amerock Grace Revitalize Knob For Cabinets

Amerock Grace Revitalize knob gives cabinets a satin nickel 1-3/8 in diameter pull point that suits professional shop builds and serious DIY work. The knob sits on a 11/16 in base diameter, so it lands with a defined footprint that helps visually anchor doors and drawers. Its 1-3/16 in projection brings the grip away from the front, giving fingers room to grab without scraping knuckles against the surface. The zinc material provides a solid-feeling knob body that supports everyday cabinet use in kitchens, baths, or built-ins. Satin nickel finish delivers a muted metallic look that works well across many door styles, from painted to stained wood. With its round profile and consistent sizing, this knob helps keep layouts uniform across banks of doors and drawer fronts.

Key Grace Revitalize Knob Details In Use

• The 1-3/8 in (35 mm) diameter knob face creates a broad contact area that is easy to grab, helping doors and drawers open with less effort on heavier cabinet fronts.
• The 1-3/16 in projection holds the hand away from the cabinet face, which reduces contact between fingers and finished surfaces during use and can help limit finish wear.
• The 11/16 in base diameter keeps the contact ring compact, which helps the knob sit cleanly on narrower rails or stiles where space around the mounting hole is tight.
• The satin nickel finish brings a consistent, low-glare metallic look that pairs smoothly with many hinge and faucet finishes for coordinated hardware runs.
• The zinc material forms a sturdy knob body that supports repeat pulls over time, important on busy kitchen doors and frequently used drawer fronts.

Amerock Knob Fit, Size, And Mounting Basics

This Amerock Corporation knob registers as a 1-3/8 in length or diameter unit, so layout work revolves around a single consistent size across the job. The 1-3/16 in projection defines how far it stands off the cabinet, which helps when checking clearance near adjacent walls, appliances, or trim. With an 11/16 in base diameter, the knob centers neatly over standard drilled holes without overwhelming narrow framing on smaller doors. The specified 8-32 x 1 screw size gives a matching thread and shaft length for common cabinet door and drawer fronts, supporting straightforward mounting into predrilled holes. Together, these dimensions guide hole placement, spacing, and alignment when planning out new runs or matching existing layouts.

Using This Satin Nickel Knob In Real Projects

Where The 1-3/8 In Diameter Knob Works Well

This knob sits in the Decorative Hardware & Moldings category under knobs, so it is suited to cabinet doors and drawer fronts in kitchens, baths, and built-in storage. The 1-3/8 in diameter face offers enough surface to grip on medium and large doors, which helps when opening wider pantry or base cabinets. On drawers, the same diameter keeps the look balanced, avoiding an undersized pull point on standard 15 to 24 in widths. The satin nickel finish coordinates with many contemporary and transitional projects, tying into similar satin nickel components already common in woodworking and cabinet hardware lines. Being part of the Amerock Grace Revitalize collection also means it carries a consistent visual language that can run across an entire room or project.

Details That Support Consistent Installation Results

The specified 8-32 x 1 screw size sets expectations for the mounting interface, which aligns with typical cabinet drilling practices and helps keep installs repeatable from door to door. A 1-3/16 in projection gives a known stand-off, so installers can line up this knob with adjacent hardware and anticipate how far it will extend relative to neighboring doors or appliances. The 11/16 in base diameter focuses the load around the mounting point, helping the knob sit flush and stable against flat cabinet faces without crowding narrow rails. With a 1-3/8 in length or diameter, template work becomes straightforward because every knob on the run shares the same centerpoint and visual mass. Tying these fixed dimensions together allows more predictable drilling, cleaner alignment, and less rework on finished fronts.

Common Questions About The Amerock Grace Revitalize Knob

Choose This Knob For Sized, Satin Nickel Pull Points

The Amerock Grace Revitalize knob in satin nickel brings a 1-3/8 in diameter zinc body, a 1-3/16 in projection, and a 11/16 in base diameter to cabinet doors and drawers. Those fixed dimensions turn into predictable layout work when spacing hardware across face frames and drawer banks. The 8-32 x 1 screw size supports direct mounting into standard cabinet fronts, simplifying the step from drilling to final install. For projects that call for a coordinated satin nickel look under the Amerock name, this BP36628G10 knob offers a clearly defined size, shape, and finish to integrate into your next run.