Extruded aluminum angle mill finish defines this 12 foot length from Paramount Extrusions Company, giving you a straight, consistent right-angle profile that supports accurate panel assembly work over long runs. The 1-1/2 inch by 1-1/2 inch dimensions provide equal legs, so installers can reference either side when aligning panels, frames, or related components in fastener and Z-clip layouts. The 0.125 inch thickness creates a sturdy corner profile while still allowing straightforward cutting and drilling during shop or onsite fabrication. The aluminum material keeps weight down compared to steel, which helps when working overhead or handling longer pieces. Mill finish aluminum offers a clean, unfinished surface, so fabricators can leave it as-is for concealed applications or prepare it for secondary finishing processes when a specific aesthetic or additional protection is required on a project.
The 1-1/2 inch projection, identified as dimension A, sets the reach of each leg from the corner, giving installers a clear expectation of how far the aluminum angle will extend along mating surfaces in a panel assembly fitting. Matching 1-1/2 inch width on the other leg keeps the profile square and even, which simplifies aligning this angle with Z-clip systems and related fastener layouts in woodworking or panel work. The 12 foot overall length gives fabricators room to cut multiple shorter pieces from one extrusion while still having enough continuous length available for longer edges. A 0.125 inch thickness supports reliable fastening and edge stability when used as a structural guide or trim component in a panel assembly context.
This extruded aluminum material is classified under panel assembly fittings, positioning it for use where panels, components, or frames need a straight, right-angle reference in fastener-based or Z-clip arrangements. The equal 1-1/2 inch legs provide a consistent 90-degree profile, which suits layouts where one leg supports a panel edge while the other leg ties into a supporting surface or framing element. In projects using Z-clips within the fasteners category, this aluminum angle can serve as a structural guide or edge support, helping panels sit true to the intended line. The 12 foot length works well in shop environments where multiple custom sizes are cut from stock, supporting both small assemblies and extended panel runs without changing material type mid-project.
The 1-1/2 inch by 1-1/2 inch leg design gives installers a predictable reference on both faces, which aids in keeping corners square when setting up panel assembly fittings. The 0.125 inch thickness balances rigidity with workable material, so drilling or fastening operations can proceed without excessive deformation along the edge. Mill finish aluminum offers a uniform raw surface, giving fabricators a consistent starting point whether the angle is left unfinished in concealed locations or prepared for coating in visible areas. The aluminum material keeps the extrusion manageable over its full 12 foot length, supporting more controlled handling at benches or lifts. Listed radii values r, r1, r2, and r3 at 0.015 inch define the small corner transitions in the profile, which matters when panels or mating parts are detailed closely to the angle geometry for tight-fitting work.
The aluminum angle has 1-1/2 inch projection and 1-1/2 inch width, with a 0.125 inch thickness, providing equal legs and a sturdy profile for panel assembly layouts.
The Paramount Extrusions Company 2073-12M aluminum angle is 12 feet long, allowing continuous runs or multiple cut lengths from a single extrusion in shop work.
The product is extruded aluminum with a mill finish, giving a raw aluminum surface suitable for concealed use or for preparation before painting or other finishes.
The 0.125 inch thickness offers a solid yet workable profile, supporting drilling and fastening while limiting flex during assembly and installation handling.
R, r1, r2, and r3 at 0.015 inch describe small radii at profile corners, which helps when mating parts or panels are detailed closely to the aluminum angle geometry.
This product is categorized as a panel assembly fitting in the fasteners and Z-clips class, aligning it with panel-based and mounting-oriented projects.
This extruded aluminum angle mill finish piece from Paramount Extrusions Company pairs a 12 foot length with 1-1/2 inch by 1-1/2 inch legs, giving installers a consistent, workable profile for panel assembly fittings. The 0.125 inch thickness and mill finish aluminum material support cutting, drilling, and fastening around Z-clip and fastener layouts while keeping handling straightforward. For projects needing a straight, equal-leg aluminum angle within panel assembly work, this 2073-12M profile from Wurth Baer Supply provides a clearly defined geometry ready to integrate into shop or field workflows.
Sold In: 1 Each