3 inch C-Style Wood Project Clamp provides a 3 inch reach so it grips workpieces away from the edge, which helps hold joints steady while you drill, assemble, or fasten. The clamp automatically adjusts to match material thickness, so you move from one board to the next without resetting between pieces. It clamps materials up to 3 inches thick, giving enough capacity for many frame and panel assemblies. Large clamp faces spread pressure evenly across the surface, so you can hold pocket hole joints or flat parts without crushing edges. Ergonomic padded grips reduce hand fatigue as you cycle the handle through repeated clamping during a full run of parts. This clamp works with the Kreg Jig R3 Clamp Pad Adapter, as well as the Portable Base, so it ties directly into existing Kreg pocket hole setups.
This Kreg wood project clamp uses automatic adjustment to match material thickness, which keeps drill guide positions stable as you move across multiple workpieces. The 3 inch reach allows you to clamp farther from the edge, supporting pocket hole drilling and assembly where the joint sits in from the perimeter. Easy pressure control with the thumbscrew lets you dial in grip so the Kreg Jig R3 or Portable Base stays steady without crushing the stock. Large clamp faces contact more surface area, helping the jig and workpiece stay flush while you drive pocket hole screws. Ergonomic padded grips make repeated clamp-and-release motions smoother on your hands in shop or jobsite settings.
The AUTOMAXX wood project clamp adjusts automatically to match material thickness, so once you set the thumbscrew pressure you can move from one piece to another without re-tuning the jaws. This supports pocket hole runs where material thickness changes between face frames, rails, and panels. The 3 inch reach gives access to joints that sit away from the edge, which is common when clamping across face frame widths or supporting panels behind a Kreg Jig R3. Because it works with the Kreg Jig R3 Clamp Pad Adapter, as well as the Portable Base, you can hold the jig firmly to the workpiece, which helps keep pocket holes consistent from piece to piece.
Clamping materials up to 3 inches thick (76mm) allows this clamp to secure many common furniture and cabinet stock combinations, from doubled-up parts to thicker legs and stretchers. Large clamp faces spread pressure evenly, so when you lock the jig down on thicker assemblies the load distributes across a wider area instead of concentrating at a point. Ergonomic padded grips reduce hand fatigue through repeated clamping cycles, which is valuable when drilling a long line of pocket holes or assembling multiple identical cabinets.
The automatic thickness adjustment works with the thumbscrew-controlled pressure to create a repeatable clamping setup: you set the grip once, and the jaws travel to match each new board thickness. This saves time each time you switch from 1x to thicker stock while keeping holding force predictable. The 3 inch reach places the clamp pad where it best supports the joint or jig, which helps keep parts from shifting as you drill or drive screws. Large clamp faces help keep edges flush along the joint, because the pressure spreads out instead of creating a twist at a single contact point.
Ergonomic padded grips give you a solid handhold on the clamp body so you can cycle it quickly without straining your hand, which supports steady production when repeating the same clamping motion many times. Because the clamp works with the Kreg Jig R3 Clamp Pad Adapter and the Portable Base, it fits smoothly into Kreg pocket hole workflows, allowing you to move the same clamping method between drilling stations and assembly locations while keeping parts registered the same way every time.
The 3 inch C-Style Wood Project Clamp clamps materials up to 3 inches thick (76mm), so it covers many common cabinet and furniture stock combinations during drilling and assembly.
The clamp adjusts automatically to match material thickness, so once pressure is set with the thumbscrew you can move between different board thicknesses without readjusting the jaws.
The 3 inch reach lets the clamp grip farther from the edge of the workpiece, which supports joints and pocket hole locations that sit in from the perimeter during assembly.
Large clamp faces spread pressure evenly over the surface, helping protect softer woods from dents while pulling joints together across a wider contact area.
The clamp uses a simple thumbscrew to regulate pressure, giving you direct control over how tightly the jaws hold different materials during drilling and assembly tasks.
The clamp works with the Kreg Jig R3 Clamp Pad Adapter and the Portable Base, so it holds the jig firmly to the workpiece for steady pocket hole drilling and assembly.
The Kreg KHC3 3 inch C-Style Wood Project Clamp combines automatic thickness adjustment, a 3 inch reach, and capacity for materials up to 3 inches thick to support common pocket hole and assembly tasks. Large clamp faces and ergonomic padded grips help keep joints stable while staying comfortable through repeated use. Its compatibility with the Kreg Jig R3 Clamp Pad Adapter and the Portable Base ties it directly into Kreg pocket hole workflows. Choose this AUTOMAXX wood project clamp from Wurth Baer Supply when you want a clamp that aligns with established Kreg drilling and assembly setups.
Sold In: 1 Each