Automaxx right angle clamp holds pocket-hole joints at a fixed 90 degree angle during project assembly, which keeps mating parts aligned while you drill, fasten, or dry fit the work. The clamp is designed as a clamping tool for pocket-hole joints, so it supports both professional woodworking setups and serious DIY builds that rely on pocket-hole joinery. The built-in Automaxx technology adjusts automatically to different material thicknesses, so the same clamp can grip a range of workpieces without manual re-setting between steps. This automatic thickness adjustment keeps clamping pressure consistent from part to part, which helps joints pull up tight and reduces time spent dialing in the setup. A contoured grip on the handle supports comfort while clamping and releasing, which matters over repeated cycles on larger cabinet or furniture runs.
This Kreg right angle clamp is built for woodworkers working with pocket-hole joints, so its 90 degree holding action directly supports assembly workflows. The pin that fits into the pocket hole establishes the first reference point, then the swivel pad engages the mating piece so the joint stays aligned as you drive fasteners. Automaxx automatic thickness adjustment allows you to clamp different material thicknesses without changing the clamp setting, which helps keep assembly moving when parts in a project vary in size. The 5 inch reach allows the jaws to access joints that sit away from the edge, supporting cabinet carcasses, face frames, and similar assemblies. Contoured grips on the handle support comfortable actuation, which matters when repeating the same clamping motion across multiple joints.
This pocket-hole right angle clamp is part of the Kreg Tools family of clamping tools, positioned for woodworking shops and serious hobby benches that rely on pocket-hole joinery. By holding pocket-hole joints at 90 degrees, it supports assembly of frames, cases, and similar structures where square alignment is important. The pin that fits securely into the pocket hole anchors one workpiece, so the joint acts like it is fixtured while you fasten it. The swivel pad then holds the mating piece, so the clamp effectively grips both sides of the joint using surfaces that match typical woodworking materials. With a 5 inch (127mm) reach, the clamp can work on joints that are not at the very edge of a board, supporting cabinet interiors and deeper assemblies built from multiple components.
The Automaxx technology is central to how this KHCRA right angle clamp maintains consistency across many joints. By adjusting automatically to material thickness, the clamp can move from one thickness to another while maintaining functional clamping pressure, which supports repeatable results when a project mixes different stock sizes. Holding pocket-hole joints at 90 degrees keeps fasteners entering at the intended angle, helping joints seat properly as they draw together. The pin in the pocket hole and the swivel pad on the mating piece work together to resist slipping during fastening, so the joint alignment achieved during clamping is the alignment that remains in the finished assembly. Contoured grips give the user a shaped contact point on the handle, which supports control over the clamping action and comfortable repetition across a full build.
The Automaxx right angle clamp holds pocket-hole joints at 90 degrees during project assembly, which supports applications where pocket-hole screws are used to join two workpieces.
The Automaxx technology adjusts automatically to material thickness, so the clamp maintains grip as you move between different stock sizes without resetting the clamping mechanism each time.
The pin fits securely into the pocket hole, anchoring one workpiece so the joint stays located while the swivel pad engages the mating piece and you drive fasteners.
The 5 inch (127mm) reach allows the clamp jaws to access joints that sit away from the edge of a board, which is useful for cabinet interiors and frame assemblies.
The contoured grips provide added comfort when operating the clamp, which supports repetitive clamping and releasing during larger woodworking or cabinet projects.
The swivel pad holds the mating piece against the joint, spreading pressure over the surface so the two parts draw together tightly while staying aligned.
This woodworking right angle clamp from Kreg Tool is built specifically for pocket-hole joints, combining a pin that fits securely into the pocket hole with a swivel pad that holds the mating piece. Automaxx automatic thickness adjustment lets it handle different material thicknesses in the same workflow, while the 5 inch reach and contoured grips support frequent use on cabinetry, furniture, and similar projects. For woodworkers needing controlled 90 degree holding on pocket-hole joints, this clamp offers focused support for assembly tasks.
Sold In: 1 Each