Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Fastmount Center Point Low Profile is a panel assembly fitting from the Low Profile Series that fits into Low Profile Series female clips to mark the hole center in the panel for correct clip alignment, helping installers position matching clips accurately. This center point belongs to the Fastmount panel mounting systems category of panel assembly fittings, so it works as a setup tool rather than a permanent fastener, supporting efficient layout on jobs using Low Profile Series clips. The Fastmount brand identity ties it directly to Low Profile Series female clips, which matters when a panel mounting system is already specified and alignment between mating parts must be repeatable. The manufacturer part number CP-08ST identifies this exact Low Profile Series center point, which simplifies reordering when multiple crews need the same alignment tool across projects.
This Fastmount CP-08ST center point fits into Low Profile Series female clips to mark the hole center in the panel for correct clip alignment, so drill points come directly from installed clips rather than measured offsets. By using the female clip as the physical reference, the marked hole center in the panel reflects the clip position, which helps panels seat properly when mounted. As part of Fasteners and Panel Mounting Systems within panel assembly fittings, this center point integrates into established Fastmount workflows, so installers can move from clip placement to panel drilling using the same system references.
The Fastmount, Center Point with Stainless Steel Tip Low Profile Series is used within the Fastmount panel mounting systems category, so it fits panel assembly workflows that rely on Low Profile Series female clips. Because it fits into Low Profile Series female clips to mark the hole center in the panel for correct clip alignment, it is applied wherever those female clips are fixed to a substrate and matching panel holes are needed for aligned clip engagement. In the panel assembly fittings class, this CP-08ST center point helps bridge the gap between clip installation on framing or carcasses and drilling matching panel holes, which is especially useful when multiple panels must align to the same Low Profile Series layout. By taking its position directly from each female clip, the tool allows panel hole marking in tight or obstructed areas where direct tape measurements from edges are less practical.
The Web Description states that the Stainless Steel Tip is used for marking panels made of hard materials, which means the tip is intended to create clear center marks on denser panel substrates where softer tips could deform instead of scoring. This stainless steel tip characteristic helps keep marks defined across repeated use on hard materials, supporting consistent drill centering in tougher panels. Because the tool fits into Low Profile Series female clips, the marking reference is the actual installed clip location, which reduces offset errors and helps ensure clip alignment once the panel is offered up. Being part of the Low Profile Series gives the CP-08ST a defined role in that specific clip family, so installers working with Low Profile Series female clips can standardize on this center point for alignment tasks across multiple installations.
The Fastmount CP-08ST center point fits into Low Profile Series female clips to mark the hole center in the panel for correct clip alignment, helping match panel holes to installed clips.
The center point marks the hole center in the panel directly from the Low Profile Series female clip position, which supports accurate clip alignment between substrate and removable panels.
The Stainless Steel Tip is used for marking panels made of hard materials, so it is intended to create clearer center marks where softer tips may not mark effectively.
This product is part of Fasteners, Panel Mounting Systems, and panel assembly fittings, so it functions as an alignment tool within Fastmount Low Profile Series workflows.
The Web Description states it fits into Low Profile Series female clips, so it is intended for alignment work on installations using that particular Fastmount series.
According to the description, it is sold in box quantity, 10 per box, which supports outfitting multiple installers or workstations for larger panel projects.
The Fastmount Center Point with Stainless Steel Tip Low Profile Series, manufacturer part CP-08ST, fits into Low Profile Series female clips to mark the hole center in the panel for correct clip alignment, so it directly supports accurate panel clip positioning. As a panel assembly fitting within Fastmount panel mounting systems, it is intended for marking panels made of hard materials using its Stainless Steel Tip, which benefits installers working with denser substrates. Sold in box quantity, 10 per box, it suits shop or site teams standardizing on Low Profile Series female clips for repeatable panel mounting workflows.