Wells, Zinc Die-Cast Cabinet Knobs 1-1/4" (32 mm) Square, Gunmetal Finish

Wells Series Zinc Cabinet Knob Gunmetal Use

Wells Series zinc cabinet knob gunmetal gives you a 1-1/4 inch square pull that suits cabinet doors or drawers needing a crisp, modern line. The Amerock Corporation Wells Series design uses a perfectly balanced silhouette with angled edges, so the knob presents a clean, faceted look that matches straight cabinet reveals. The zinc die-cast construction provides a solid, consistent knob body, which supports repeatable drilling layouts across a run of cabinets. The 1-1/4 inch (32 mm) diameter and width create a comfortable gripping surface for fingers, which helps when opening heavier kitchen or shop fronts. The gunmetal finish delivers a darker, refined tone, so it visually ties in with other dark decorative hardware and moldings on the job.

Key Wells Series Cabinet Knob Advantages

• The 1-1/4 inch (32 mm) square size gives a defined footprint, which helps align multiple knobs across doors and drawers for a uniform sightline.
• The zinc die-cast material forms a single, solid knob body, which supports consistent feel from one cabinet position to the next.
• The gunmetal finish creates a dark, muted surface, which helps the knob blend with gunmetal-colored hinges or pulls in the same space.
• The 1-3/16 inch (30 mm) projection sets the knob off the face, which provides finger clearance while keeping the pull close to the door plane.
• The 5/8 inch (16 mm) base length and 5/8 inch (16 mm) base width define a compact footprint at the contact point, which helps when laying out tight rail or stile areas.

Mounting And Orientation Details For BP36546GM

The Wells Series BP36546GM knob uses a square 1-1/4 inch (32 mm) form, which lets you mount it in line with cabinet edges or diagonally across the corner. Mounting at 45 degrees creates a diamond shape, so you can match angled design lines in a contemporary layout. The 1-3/16 inch (30 mm) projection establishes how far the knob stands off the cabinet face, which is useful when planning clearances near adjacent doors or tall pulls. The specified screw size of 8-32 x 1 inch sets the thread and length requirement at the mounting point, which matters when drilling and tapping through typical cabinet door thicknesses.

Using The Amerock Wells Knob In Real Projects

Where The Wells Series Square Knob Fits Best

The Amerock Corporation Wells Series zinc die-cast cabinet knob works in decorative hardware and moldings projects that call for a square profile. The 1-1/4 inch (32 mm) width pairs well with standard cabinet door and drawer fronts, so it suits kitchens, baths, and casework that benefit from a geometric pull point. The perfectly balanced silhouette with angled, gemstone-like edges adds defined lines, which helps tie together flat-panel or shaker-style doors that rely on straight geometry. When mounted at 45 degrees to form a diamond shape, the knob can echo diagonal tile patterns or angled grain directions, which is useful when aligning hardware design with other installed finishes. The 5/8 inch (16 mm) base length and 5/8 inch (16 mm) base width keep the contact area compact, so the knob can be positioned on narrow rails or stiles without crowding edges.

Details That Support Repeatable Wells Knob Results

The Wells Series zinc die-cast cabinet knob gunmetal finish is built around predictable dimensions, which supports repeatable layouts across multiple cabinets. The 1-1/4 inch (32 mm) square size and 1-3/16 inch (30 mm) projection define fixed reference points, so drilling jigs can be set once for a full run. The zinc die-cast construction provides a uniform casting, which helps keep each BP36546GM knob consistent in feel and size from one opening to the next. The 8-32 x 1 inch screw size defines the fastening interface, which simplifies selecting the correct tap or clearance hole during installation. The gunmetal finish keeps the visible surface consistent in color, so knobs across a bank of cabinets match when viewed under the same lighting. These fixed details let installers plan hardware placement, clearance, and aesthetics using reliable dimensions on every piece.

Common Questions About The Wells Series BP36546GM

Selecting This Wells Knob For Your Project

The Amerock Corporation Wells Series zinc die-cast cabinet knob in gunmetal finish offers a 1-1/4 inch (32 mm) square profile with a 1-3/16 inch (30 mm) projection, giving cabinets a defined pull point. The option to mount it at 45 degrees creates a diamond presentation, so the same BP36546GM knob can support either linear or angled design themes. With fixed dimensions, zinc die-cast construction, and gunmetal finish, this Wells Series knob lets you plan decorative hardware and moldings layouts around known measurements and a consistent visual tone.