M4 x 8mm countersunk screw gives you a metric fastener sized for Euro-style hinge work, so you can match modern hardware layouts without hunting for odd sizes. The countersunk head design seats flush in compatible hinge or plate holes, which keeps the hinge face sitting tight to the door or panel for a clean, consistent reveal. The internal hex key drive lets you apply torque with a hex bit or key, helping you avoid cam-out when you are driving into dense materials. With an M4 thread and blunt point, this screw is set up for pre-bored applications where you want thread engagement without a sharp tip wandering or damaging the hole. The SAP description identifies it as a nickel M4 x 8mm countersunk screw, so you are working with a clearly defined, repeatable spec.
The web description states that this countersunk screw is for chipboard, MDF, mineral composite, and HPL, so it targets the common engineered substrates used in cabinet and fixture doors. A minimum door thickness of 5/16 inch is specified, which sets a clear lower limit for applications and helps align the screw length with typical Euro hinge drilling depths. The sleeve is noted as M4 x 1/4 inch, so the hardware system it belongs to uses coordinated metric dimensions for both screw and sleeve. Because the head is countersunk and driven with an internal hex key, you can bring the hinge or plate down snug to the door surface without a proud head or slipping driver.
The product name describes this as an 8mm x 5/16 inch countersunk head Euro screw with hex drive, M4 thread, blunt point, nickel finish, and a minimum door thickness of 5/16 inch, so it is aligned with Euro-style hinge installations on engineered doors. The web description ties it directly to chipboard, MDF, mineral composite, and HPL, which are common substrates in cabinet, closet, and commercial panel work where reliable hinge anchoring is critical. The M4 x 1/4 inch sleeve reference confirms it is part of a metric hinge fastening system, so the screw and sleeve dimensions work together when you are following a coordinated drilling pattern. As a Grass America product in the hinge screws and accessories class, it supports hinge setups that rely on accurately sized Euro screws.
The internal hex key drive on this screw means you can use a matching hex bit to drive fasteners into dense chipboard, MDF, mineral composite, or HPL panels with a reduced tendency for the driver to slip during installation, which supports consistent clamping of hinge parts. The countersunk head profile works with countersunk holes in hinge components, so when the screw is tightened, the head centers in the seat and helps pull the hardware square to the door face. With an 8mm length and blunt M4 tip, the screw engages threads inside the drilled hole without extending far beyond the specified 5/16 inch minimum door thickness, which helps keep the fastener working within the material rather than protruding. The nickel designation in the SAP description identifies the finish on the M4 x 8mm countersunk screw, so its appearance is coordinated when the head is visible at the hinge connection point.
The Grass F072135928201 is an M4 x 8mm countersunk head Euro screw with internal hex key drive and blunt point, so it is suited to metric hinge fastening in prepared holes.
This M4 x 8mm countersunk screw is described for chipboard, MDF, mineral composite, and HPL, so it focuses on common engineered door and panel materials used in cabinetry.
This hinge screw is specified for a minimum door thickness of 5/16 inch, aligning its 8mm length with typical Euro hinge drilling depths in thin engineered doors.
The internal hex key drive lets installers use a hex driver for solid bit engagement, which supports controlled torque when driving into dense chipboard, MDF, or composite panels.
The blunt M4 point works with pre-bored holes in engineered materials, engaging threads without a sharp tip that could wander or chip the hole edges.
The sleeve M4 x 1/4 inch noted in the description indicates a matching metric sleeve, so the screw and sleeve dimensions coordinate within the hinge fastening system.
This nickel M4 x 8mm countersunk screw from Grass America, with internal hex key drive, blunt M4 thread, and a stated minimum door thickness of 5/16 inch, provides a defined fastener setup for Euro-style hinge work in chipboard, MDF, mineral composite, or HPL doors. When a project calls for a countersunk head Euro screw matched to an M4 x 1/4 inch sleeve, choosing the Grass F072135928201 part number aligns your hinge fastening with the described metric system.
Sold In: 1 Each