Liberty Devereux Series 6-5/16" (160 mm) Center to Center Heirloom Silver Pull, - P34961-904-C

Liberty Devereux Series Pull For Cabinet Projects

Liberty Devereux Series pull is a zinc die cast cabinet handle in an Heirloom Silver finish that provides a consistent look across doors and drawers. The pull uses a 6-1/4 inch center to center layout, so it lines up with standard 160 mm boring for many cabinet runs. Its total length of 7-5/8 inches spans wider drawer fronts, giving a balanced visual across face frames or full-access boxes. The 11/16 inch projection stands the pull slightly off the surface, creating finger clearance while keeping the profile close to the cabinetry. A width of 1-3/16 inches offers a comfortable gripping surface, which helps on heavier drawers. The Liberty Hardware Devereux collection identity keeps style unified when the same pull is repeated on multiple openings.

Key Devereux Pull Details For Cabinet Work

• The zinc die cast material creates a solid-feeling pull body that supports repeated everyday cabinet use across kitchens, baths, or shop-built casework.
• The Heirloom Silver finish defines the appearance of the pull, helping it coordinate with similar toned hinges or decorative hardware on the same installation.
• The 6-1/4 inch center to center measurement allows accurate drilling and boring, which supports consistent alignment of multiple pulls in a run of doors and drawers.
• The overall 7-5/8 inch length distributes the hand contact area over a wider section of the front, helping larger drawers feel easier to open.
• The 11/16 inch projection sets a defined stand-off from the door or drawer face, providing room to grip while limiting how far the hardware extends into the room.
• The 1-3/16 inch width gives a stable gripping surface, which can help users grab the pull comfortably from different angles on tall or base cabinets.

Mounting And Sizing Details For This Cabinet Pull

The 6-1/4 inch center to center dimension on this Liberty Hardware Devereux pull establishes the hole spacing for mounting, which guides jig setup and template use during cabinet fabrication. With an overall length of 7-5/8 inches, the pull covers the boring pattern while leaving consistent margins at each end on typical drawer fronts. Its 11/16 inch projection defines how far the handle stands off the surface, which can be important when planning clearances near adjacent doors or walls. The 1-3/16 inch width describes the front-facing footprint, helping position the pull so it looks balanced on narrow doors or wider drawer rails. Together, these measurements support repeatable placement on a full room of cabinetry.

Using The Devereux Heirloom Silver Pull In Builds

Where This Liberty Devereux Series Pull Fits Best

This Liberty Devereux Series pull is part of the Deverux collection from Liberty Hardware, giving it a defined style family for use on coordinated installations. The 6-1/4 inch center to center boring works well on medium to large cabinet doors, where the extended length helps the pull sit in proportion to the stile and rail layout. On drawer fronts, the 7-5/8 inch overall length provides a comfortable span across common drawer widths, which can be helpful on kitchen bases, bathroom vanities, or storage cabinets. The Heirloom Silver finish lets the pull act as a visible hardware element, so it can be chosen to work alongside other decorative components in the same space.

Why These Dimensions Support Consistent Cabinet Results

The defined 6-1/4 inch center to center spacing on the P34961-904-C cabinet pull lets installers rely on the same measurement across an entire job, reducing layout variations when drilling multiple fronts. Its 11/16 inch projection keeps the gripping point close to the face, which can help doors open smoothly without requiring an exaggerated pull angle. The 1-3/16 inch width gives fingers a stable surface to catch from above, below, or the side, supporting comfortable use on both wall and base cabinets. Because the pull is zinc die cast, the body maintains its shape under regular handling, which supports long-term alignment of the hardware on the cabinet face. The Heirloom Silver finish defines the visual presentation of these dimensions, keeping the installed pulls looking unified from piece to piece.

Common Questions About This Liberty Devereux Pull

Selecting This Heirloom Silver Pull For Your Job

The Liberty Devereux Series pull in Heirloom Silver combines a zinc die cast construction with a 6-1/4 inch center to center layout, supporting consistent drilling across multiple fronts. Its 7-5/8 inch overall length, 11/16 inch projection, and 1-3/16 inch width define a practical profile for doors and drawers. For projects that need coordinated decorative hardware, this P34961-904-C cabinet pull provides a clearly specified size and finish that fit into cabinet layouts with predictable results.