Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Aluminum Z-clip 3 inch design supports straightforward hanging of cabinets and panels in panel assembly fittings work. The clip is part of the EA10812 Series extruded aluminum short hang clip line, so it follows a consistent profile that pairs with a matching long wall clip. The web description states that the long wall clip attaches to the wall while the short hang clip attaches to a cabinet or panel, creating an interlocking connection that transfers load through the clips instead of relying only on face fasteners. The short hang clip length of 3 inches provides a compact mounting point that is easy to position along the cabinet or panel edge. With a width of 1-5/8 inches, the clip presents a stable bearing surface that spreads contact across the mating parts, helping the assembly sit flush when correctly aligned.
The web description specifies that the long wall clip attaches to the wall, while the short hang clip attaches to a cabinet or panel, so installation proceeds in two stages: fixed wall positioning and separate panel preparation. The 3/8 inch lift off stated in the SAP and web descriptions establishes how far the hanging panel or cabinet sits away from the wall-mounted clip, which defines the working stand-off for the assembly. Overall dimensions of 1.625 inch width by 3 inch length supply a clear rectangular footprint that informs drilling patterns for the three available holes referenced in the SAP description. Because the clip is an extruded aluminum part in the EA10812 Series, the mating geometry between the wall clip and the short hang clip is set by the extrusion profile, promoting repeatable engagement when the two pieces are brought together.
The product is categorized under panel assembly fittings and fasteners with the Z-clips classification, which places it directly in panel and cabinet hanging applications where an interlocking connection is required. The web description notes that the short hang clip attaches to a cabinet or panel, so this element becomes part of the back or structural edge of the component being mounted. The corresponding long wall clip attaches to the wall, creating a separate fixed reference that defines the final position of the cabinet or panel once the short hang clip is engaged. With an overall footprint of 1.625 inch width and 3 inch length, the short hang clip is sized for use on typical cabinet rails, panel backs, or framing members where a compact yet stable hanger is preferred. The 3/8 inch lift off gives a predictable offset once engaged, which is useful when aligning adjacent panels that all rely on the same clip geometry to meet at a consistent plane.
The SAP description explicitly states 3/8 lift off, and that value defines how much separation exists between the wall-mounted and panel-mounted parts when the interlocking Z-clips are fully seated. This fixed offset helps panels or cabinets clear small wall irregularities and allows the mounting surfaces to nest on the clip profile instead of bearing directly against the wall. The listed A dimension of 0.375 directly corresponds to 3/8 inch, tying the dimensional callout to the lift off behavior, so installers know this measurement refers to the working stand-off in the assembled condition. The B dimension of 0.200 describes another portion of the clip geometry, giving further detail about the profile that influences how the mating long wall clip engages the short hang clip. With three holes noted in the SAP description, the fastener pattern can cover the length of the 3 inch clip, so loads are spread along the extruded aluminum body during use. The EA10812 Series designation and manufacturer part number 10812-C together identify the specific profile, which supports consistent selection across projects where the same clip behavior and dimensions are required.
The 10812-C Z-clip has overall dimensions of 1.625 inch width by 3 inch length, so layouts can be planned around that footprint on cabinets or panels.
The EA10812 Series short hang clip attaches to the cabinet or panel and mates with a long wall clip on the wall, creating an interlocking connection for hanging.
The 3/8 inch lift off means that when the short hang clip engages the wall clip, the panel or cabinet sits 3/8 inch off the wall-mounted clip position.
The short hang Z-clip is described as attaching to a cabinet or panel, so it mounts directly on the component that needs to be hung.
The EA10812 series short hang clip is made of aluminum, which provides a light clip body for handling during panel or cabinet assembly.
The SAP description states 3 holes on the clip, so there are three potential fastener locations along the 3 inch length.
The Paramount Extrusions Company EA10812 Series extruded aluminum short hang clip, identified as manufacturer part 10812-C, offers an interlocking Z-clip arrangement for panel assembly fittings work. With a 3 inch length, 1.625 inch width, and 3/8 inch lift off, it provides clear, repeatable geometry for cabinet or panel hanging when paired with the corresponding long wall clip. The three-hole layout described in the SAP information supports a distributed fastener pattern along the aluminum body. For projects that call for a defined stand-off and consistent engagement between wall-mounted and panel-mounted components, this aluminum Z-clip 3 inch option from Wurth Baer Supply aligns the hardware choice with the required dimensions and lift off.
Sold In: 1 Each