Cabinet Claw Face Frame Clamp combines multiple steps of face frame cabinet installation into one process, so installers pull, align, and hold frames in position without swapping tools between operations. The clamp is part of the Pony Jorgensen woodworking line, giving tradespeople a dedicated tool specifically for cabinet face frame work instead of adapting general clamps on site. The clamp is designed for professional quality installation, so it supports consistent cabinet reveals and joint alignment across a run of units. By handling face frame positioning in one motion, the tool reduces handling time on each cabinet, which helps during larger kitchen or millwork projects. The product is described as CABINET CLAW, 1 PACK, so it is supplied as a single professional-use clamp suited to repeated cabinet installations where repeatable results on stile joints matter.
The clamp is built to install two stiles in the 1-1/2 to 2 inch width range, so layout is based on typical cabinet frame dimensions used in shops and on site. Each stile can be up to 1-1/2 inch thick, allowing the clamp to engage common frame stock without reworking material to fit a lighter tool. The 4 inch opening capacity is sized to span the gap where two cabinet frames meet, so the clamp can pull the faces into alignment before fasteners are driven. Protective rubber pads on the clamp faces and the alignment plate provide a cushioned interface with finished wood, helping maintain the cabinet surface while load is applied during tightening.
The clamp is intended for face frame cabinet installation, so it fits work where two framed cabinet boxes are joined side by side in a run. By combining multiple installation steps into one operation, the clamp is suited to kitchen, bath, or built-in cabinet projects where several cabinets must line up along a wall. It is part of the Pony Jorgensen product range in the clamps class, so it sits naturally in a woodshop or installer tool kit dedicated to woodworking and cabinet assembly. The ability to handle stile widths from 1-1/2 to 2 inches and thicknesses up to 1-1/2 inches makes it relevant for standard North American framed cabinet construction using common face frame dimensions. The 4 inch opening capacity allows the tool to bridge the joint between neighboring cabinets, so it functions directly at the face frame seam where alignment is most visible after installation.
The design that combines the multiple steps of face frame cabinet installation into one process means the clamp can pull, align, and hold stiles while fasteners are driven, which helps maintain joint position and cabinet reveals without constant hand repositioning. Professional quality installation is achieved at a fraction of the time versus traditional clamps, so installers can handle more cabinets in the same workday while maintaining the same alignment standard. Protective rubber pads on both the clamp faces and the alignment plate help keep finished faces and frame edges cushioned under pressure, which supports a clean appearance on stained or painted fronts after the clamp is removed. Aluminum claws and an aluminum alignment plate provide a rigid structure that still remains relatively light, allowing installers to move the clamp quickly from one cabinet joint to the next. Because the tool is dedicated to face frame work, it supports a consistent workflow from cabinet to cabinet, helping reduce rework on misaligned frame seams.
The Cabinet Claw Face Frame Clamp is designed for face frame cabinet installation, so it holds and aligns adjoining cabinet stiles while they are fastened together.
The clamp installs two stiles from 1-1/2 to 2 inches wide and up to 1-1/2 inches thick each, covering typical face frame cabinet dimensions.
The 4 inch opening capacity allows the clamp to span the joint between adjacent cabinet face frames, pulling the frames tight before fastening.
Protective rubber pads on the clamp faces and alignment plate cushion cabinet surfaces, reducing marring while still applying holding pressure.
The clamp uses aluminum claws and an aluminum alignment plate, providing rigid support while keeping the tool light enough for repeated repositioning.
The clamp combines multiple face frame installation steps into one process, so professional quality cabinet alignment is achieved in less time than with traditional clamps.
The Cabinet Claw Face Frame Clamp from Pony Jorgensen is built for installers who regularly join framed cabinets and want professional quality alignment in less time. With capacity for stiles from 1-1/2 to 2 inches wide, up to 1-1/2 inches thick, and a 4 inch opening, it addresses common cabinet frame dimensions used on site and in the shop. Protective rubber pads and aluminum claws support both finished surface care and repeatable clamping force across many installations. For projects that rely on accurate face frame joints, this dedicated clamp offers a straightforward way to tighten workflow around cabinet runs.
Sold In: 1 Each