Description
Berenson Traditional Advantage Two Pull For Cabinets
Berenson Traditional Advantage Two pull gives you a 3 inch center to center handle in a champagne finish that suits many cabinet styles. The pull is made from zinc, which provides a solid metal feel that stands up to regular door and drawer use in a shop or residential setting. Its total length of 4-1/2 inches offers enough hand clearance for a firm grip when opening heavier fronts. The pull projects 1 inch from the mounting surface, so fingers can get behind it without rubbing the face. A 3/8 inch width keeps the profile slim while still giving enough surface to grab comfortably during repeated operation.
Key Details That Support Cabinet Workflows
- The 3 inch center to center measurement sets consistent hole spacing, which helps layout repetitive drilling on cabinet doors and drawers across a project.
- The champagne finish creates a neutral metallic look, which helps this pull tie together different door and drawer fronts in the same run.
- The zinc material gives the pull a metal body, which supports long-term daily handling in kitchens, baths, and shop-built cabinetry.
- The 4-1/2 inch overall length offers more leverage, which can help when opening larger or loaded drawers.
- The 1 inch projection keeps the hand off the cabinet face, which reduces contact marks in high-use areas.
- The 3/8 inch width keeps the pull visually light, which can be helpful when hardware should not dominate smaller fronts.
Installation Dimensions For Hole Layout And Fit
This Berenson cabinet handle uses a 3 inch center to center dimension, so mounting holes line up on that spacing for each pull run. The base diameter of 3/4 inch around each foot gives a defined bearing surface against the door or drawer face. That base size helps cover the drilled hole area and provides a stable contact patch once fastened. With a 1 inch projection, the pull stands off the surface enough to clear common door thicknesses while keeping the hardware close to the face. The 4-1/2 inch overall length can also be used as a reference when aligning multiple pulls across wider drawer fronts.
Using This Champagne Pull In Cabinet Projects
Where This 3 Inch Center Pull Performs Best
This 3 inch center to center cabinet pull from the Traditional Advantage Series works well anywhere that standard 3 inch drilling is part of the cabinet plan. The zinc construction handles regular opening and closing cycles on kitchen, bath, or shop storage fronts. A champagne finish adds a soft metallic tone that coordinates with many door colors without dominating the design. The 4-1/2 inch length gives enough span for adult hands, which helps when hardware must work for different users. Because the base diameter is 3/4 inch, the pull seats well on typical cabinet rail and stile widths, helping maintain a balanced look on narrow or wider frames.
Details That Support Consistent Hardware Alignment
The defined 3 inch center to center spec lets installers set up jigs or drilling templates once, then repeat that pattern across all fronts for uniform hardware lines. A 1 inch projection gives predictable hand clearance, which simplifies planning when fronts are close to adjacent walls or appliances. The 3/8 inch width keeps the pull low bulk, which can be helpful when multiple drawers are stacked closely and hardware spacing is tight. With a 3/4 inch base diameter, each foot covers the fastener area, helping achieve a clean finished look around the mounting points. The consistent geometry of length, projection, and base size supports straight visual lines when many pulls are installed in rows.
Common Questions About This Berenson Cabinet Pull
What is the center to center size of this pull?
The Berenson Traditional Advantage Two pull has a 3 inch center to center measurement, which matches common cabinet drilling patterns and simplifies layout on multiple doors and drawers.
What material is the Berenson 9188-10CZ-P pull made from?
The 9188-10CZ-P pull is made from zinc, giving it a solid metal construction suited to frequent cabinet door and drawer use.
How far does this cabinet pull project from the surface?
This cabinet pull has a 1 inch projection, providing finger clearance behind the handle while keeping the hardware close to the door or drawer face.
What is the overall length of this champagne pull?
The pull has a 4-1/2 inch overall length, offering a comfortable gripping span across the front of cabinet doors and drawers.
How wide is the Berenson Traditional Advantage Two pull?
The pull is 3/8 inch wide, giving it a slim profile that provides grip while keeping the visual look light on cabinet fronts.
What is the base diameter on each end of the pull?
Each end of the pull has a 3/4 inch base diameter, creating a stable contact area against the cabinet surface and covering the mounting hole area.
Select This 3 Inch Champagne Pull For Your Next Run
The Berenson Traditional Advantage Two pull with 3 inch center to center spacing, zinc construction, and champagne finish offers a defined set of dimensions for consistent cabinet work. Its 4-1/2 inch length, 1 inch projection, and 3/4 inch base diameter provide clear references for layout across doors and drawers. When a project calls for a slim 3/8 inch wide handle that suits standard drilling patterns, this pull aligns well with that requirement.