Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Sugatsune CN Series tab pull gives a low-profile brass edge pull for cabinets where a clean face is important. The satin nickel finish provides a muted metallic look that suits modern millwork, so fronts stay visually consistent across a run of doors or drawers. The pull uses a 4-7/8 inch (123 mm) center to center dimension, which sets hole spacing for drilling jigs and layout on cabinet edges. A total length of 137 mm gives enough fingertip surface to grab, helping with everyday opening without needing a bulky handle. The 1-7/16 inch height establishes how far the pull stands along the door edge, which affects hand clearance around adjacent fronts. A 7/8 inch width defines the visible strip at the edge, helping plan reveals, door overlays, and how the pull lines up with neighboring fronts on an installation.
This satin nickel tab pull is defined by a 4-7/8 inch (123 mm) center to center dimension, which dictates the spacing of the two mounting points along the cabinet edge for precise drilling. The 137 mm overall length positions those holes relative to the pull ends, which helps keep reveals consistent when aligning several pulls in a line. Its 1-7/16 inch height describes the extension along the door edge, affecting how far the pull presents to the user when the door is closed. A 7/8 inch width defines how much of the edge is covered, which matters when coordinating with edge banding, door thickness, and nearby panels. The 3.1 x 16 screw size provides a clear target for fastener selection that suits standard cabinet door materials and common boring depths.
The Sugatsune CN Series tab pull in satin nickel is suited to cabinet doors or drawers where an edge pull is preferred over a projecting handle, because its 1-7/16 inch height follows the edge rather than standing far off the face. The 7/8 inch width keeps the visible hardware strip narrow, which works well on frameless or full-overlay fronts where hardware should stay subtle. A center to center dimension of 4-7/8 inches (123 mm) works across many standard door sizes, so one drilling setup can cover upper cabinets, bases, and tall units. The 137 mm overall length aligns with that center spacing, making the pull visually balanced on medium-width fronts. Brass construction supports use in typical residential and commercial cabinet environments where metal pulls are expected.
The CN-A360 edge pull uses the 4-7/8 inch (123 mm) center to center spacing as a repeatable drilling reference, letting installers build jigs so every pull aligns along a cabinet run without re-measuring. The 137 mm overall length ties directly to that spacing, so once the first pull is positioned, subsequent pulls visually match at the same distance from door corners. With a 1-7/16 inch height, the pull offers a predictable grip band along the edge, helping fabricators design door thickness and overlay with known clearance. The 7/8 inch width keeps the hardware footprint controlled, which reduces conflict with tight reveals or adjacent doors. The brass material and satin nickel finish together provide a consistent feel and appearance, reducing callbacks tied to mismatched finishes in a project.
The CN-A360 tab pull has a 4-7/8 inch (123 mm) center to center dimension, which defines the spacing for drilled mounting holes on cabinet doors or drawers.
The Sugatsune CN-A360 edge pull is 137 mm long, so the pull extends beyond the mounting points enough to give a balanced grip area along the cabinet edge.
The satin nickel CN Series pull has a 1-7/16 inch height and 7/8 inch width, defining how much of the door edge it covers and how much grip surface is available.
The CN-A360 tab pull is made from brass, giving a metal body that suits cabinet applications where a solid-feeling edge pull is required.
This Sugatsune cabinet tab pull uses a satin nickel finish, providing a soft, brushed look that coordinates with many contemporary hinges and appliances.
The CN-A360 edge pull is specified with a 3.1 x 16 screw size, which guides fastener selection for mounting into typical cabinet door materials at common depths.
The Sugatsune CN Series tab pull CN-A360 combines brass construction, satin nickel finish, and 4-7/8 inch (123 mm) center to center spacing for consistent cabinet layouts. When a 137 mm edge pull with a 1-7/16 inch height and 7/8 inch width fits your door sizes and reveals, this satin nickel option keeps hardware lines clean across the project.