63.1mm rubber hat coat hook green identifies this Sugatsune America decorative hook as a compact, color-specific solution for hanging items in woodworking and interior projects where size and look both matter. The hook is part of the Decorative Hooks class, so it functions as visible hardware rather than hidden support, which matters when selecting pieces that must coordinate with finished millwork. Its green finish is described as vivid but not too bright, which helps it stand out enough for everyday use while still blending with a wide range of cabinet and wall colors. The height of 3 inches and projection of 2-1/2 inches define how far hats or coats sit off the surface, which is important when planning clearances near doors, panels, or adjacent hooks. A width of 9/16 inch concentrates support, which helps keep smaller items from shifting sideways while hanging.
The 63.1mm Rubber Hat/Coat Hook, Green, uses a size 4 x 32 pan head tapping screw, which gives a defined fastener size for mounting into suitable surfaces during installation. The stainless steel base sits behind the soft silicone rubber cover, so the structural load transfers through metal while the user contacts only the softer exterior, which matters when positioning the hook at hand or head height. The projection of 2-1/2 inches creates space between the mounted surface and the hanging point, which helps coats and hats clear trim or door hardware near the hook. The 9/16 inch width keeps the mounting area narrow, allowing installers to place several hooks along a rail or board without crowding.
This Sugatsune America decorative hook belongs to the Decorative Hardware & Moldings category, which makes it suitable for exposed locations on cabinetry, wall panels, or millwork where appearance matters as much as function. The green silicone rubber cover, described as vivid but not too bright, allows it to serve as a color accent on coat racks, locker panels, or entry cabinetry without overwhelming surrounding finishes. Its 3 inch height keeps the form compact, so it integrates easily on narrow stiles, end panels, or closet side walls without interfering with adjacent components. The 2-1/2 inch projection provides enough stand-off to hang typical hats or light coats without pressing them tightly against the surface, which is useful when hooks are used on finished doors or decorative panels. With a width of 9/16 inch, the hook occupies minimal horizontal space, allowing a row of hooks to be laid out at regular intervals along a rail for organized hanging. As a decorative hook, it contributes to both the visual design and everyday function of woodworking and interior projects.
The base made from stainless steel provides the structural core of the hook, which helps it hold items securely in place and maintain alignment after repeated use. Over this base, the soft silicone rubber cover supplies the contact surface, which helps protect garments while still gripping them. The inside of the silicone cover is equipped with an anti slip feature, which significantly reduces the chance the cover will be accidentally removed, so the installed hook keeps its intended shape and function over time. That anti slip feature also helps the cover stay properly seated during routine cleaning or when items are pulled off at an angle, maintaining a consistent feel for users. The charming rounded shape of the silicone-covered hook reduces abrupt edges, which is beneficial in high-traffic areas where people may brush against the hardware. Because the colors are vivid but not too bright, installers can repeat the same hook across multiple rooms or fixtures while maintaining a coordinated appearance that still reads clearly as a hanging point. The defined dimensions - 3 inch height, 2-1/2 inch projection, and 9/16 inch width - allow precise layout on shop drawings and in the field, supporting repeatable spacing across custom cabinetry runs or wall-mounted rails.
The 63.1mm Rubber Hat/Coat Hook, Green, has a height of 3 inches, a projection of 2-1/2 inches, and a width of 9/16 inch, which defines how it fits on panels and how far items hang from the surface.
The hook uses a stainless steel base with a silicone rubber cover, so the metal core carries the load while the soft exterior contacts hats or coats, balancing strength with gentler support for fabrics.
The inside of the silicone cover has an anti slip feature that significantly reduces the chance the cover will be accidentally removed, which keeps the hook shape and feel consistent during everyday use.
This coat and hat hook uses a size 4 x 32 pan head tapping screw, so installers have a defined screw size when preparing mounting locations in suitable substrates.
The charming rounded shape of the soft silicone rubber cover reduces sharp edges at contact points, which helps protect garments and makes bumping into the hook less abrupt in tight spaces.
The green color is described as vivid but not too bright, giving a clear visual hanging point that still coordinates with a wide range of cabinet, wall, or trim finishes in woodworking projects.
The Sugatsune America 63.1mm Rubber Hat/Coat Hook, Green, combines a stainless steel base with a soft silicone rubber cover, providing a compact decorative hook that supports hats and coats while protecting fabrics. The defined dimensions - 3 inch height, 2-1/2 inch projection, and 9/16 inch width - help plan consistent spacing across rails, cabinets, or wall panels. With colors that are vivid but not too bright and a charming rounded shape, the hook functions as both hardware and design detail. The anti slip feature inside the silicone cover significantly reduces the chance the cover will be accidentally removed, supporting long-term appearance. For projects needing a green decorative hook that balances structure and softness, this model offers clear, documented characteristics ready to integrate into your layout.