Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Maggi Steff 2032 stock feeder keeps work moving with 3 rollers, so material stays pressed to the table and fence for steadier cuts on repeated runs. The 4 speeds at 13, 26, 29, and 59 FPM let you match feed rate to cutter size or finish quality, so you can prioritize either surface finish or throughput as the job demands. The 3-1/8 inch roller diameter presents a broad contact patch to the board, which helps maintain traction across minor thickness variation. A 1-1/8 inch roller width focuses that grip in a controlled band, which supports feeding narrower stock while maintaining pressure where it matters. The 1/4 HP motor powers all three rollers, providing a dedicated drive source so feed is not affected by the main machine motor load. Complete with support stand, the unit arrives ready to be positioned at a machine for stock feeding workflows.
The Maggi Steff 2032 stock feeder uses its support stand as the structural base, which positions the 3 rollers so they can be set over the machine table and fence line for controlled feeding. With 115V, 1-phase power, the 1/4 HP motor ties into common single-phase shop circuits, so the feeder can be located at standard woodworking machinery without dedicated 3-phase service. The 3-1/8 inch roller diameter works with the stand geometry to reach over typical table heights while maintaining a useful contact arc on the board. At 78 lb, the feeder and stand assembly have enough mass to stay planted once adjusted, which helps the 3 rollers maintain their path over the stock during repeated passes.
The Maggi Steff 2032 stock feeder fits best where a 3-roller layout can sit above a table and feed line, using the support stand to reach over the work zone. The 3-1/8 inch roller diameter and 1-1/8 inch roller width suit applications where boards or profiles pass in a straight line under the feeder, so each roller can maintain contact as the piece approaches, crosses, and leaves the cutter. The 13 and 26 FPM speeds work well where slower movement supports cutters taking a more aggressive bite in a single pass, while 29 and 59 FPM speeds better suit light trimming or finer finishing cuts. With 115V, 1-phase supply, the feeder can be located at machines served by common shop outlets, which supports placing it at a shaper, router table, or similar station using standard single-phase power.
The 3 rollers on the Maggi Steff 2032 stock feeder hold material down and forward in three stages, which helps each board track along the same path relative to the fence, supporting repeatable dimension and profile location from part to part. The 4 available speeds at 13, 26, 29, and 59 FPM give flexibility to balance surface finish and feed rate, so once you dial in a speed for a specific cutter and material, you can repeat that setup to get consistent results on future runs. The 3-1/8 inch roller diameter provides a stable arc of contact that rides over minor irregularities rather than dropping into them sharply, which helps maintain steady feed pressure instead of sudden jerks. The 1-1/8 inch roller width focuses this pressure, making it easier to keep narrow or medium-width stock tight against the fence. The 1/4 HP motor supplies dedicated torque to the feed system, so feed speed stays tied to the selected setting, supporting predictable chip load across long runs. At 78 lb, the feeder and stand assembly offer a solid base, helping the roller path stay aligned once set, reducing the need for frequent repositioning.
The Maggi Steff 2032 stock feeder offers four feed speeds at 13, 26, 29, and 59 FPM, which lets you select slower speeds for heavier cuts or faster speeds for lighter passes and higher throughput.
The Maggi Steff 2032 uses 3 rollers to apply pressure in sequence, which helps keep boards against the table and fence through entry, cut, and exit for steadier, more repeatable feeding.
The 3-1/8 inch diameter and 1-1/8 inch width give each roller a stable contact area, which supports traction on the board while focusing pressure along a controlled strip during feeding.
The Steff 2032 stock feeder uses a 1/4 HP motor operating on 115V, 1-phase power, which supports use in shops wired for common single-phase circuits at woodworking machines.
The support stand gives the feeder its own structure, which lets you position the 3 rollers over the machine table and fence line so feed pressure is applied where the cutter is working.
The 78 lb weight of the Maggi Steff 2032 feeder and stand provides a solid base, helping the assembly stay stable once adjusted so the rollers track consistently over repeated passes.
The Maggi Steff 2032 stock feeder combines 3 rollers, four feed speeds from 13 to 59 FPM, and a 1/4 HP motor on 115V, 1-phase power to support controlled stock movement at common woodworking stations. The 3-1/8 inch diameter and 1-1/8 inch wide rollers work with the support stand to position reliable pressure over the board path, helping each pass follow the same line relative to the cutter. With a 78 lb assembly weight, the feeder provides a stable presence alongside your machine table, ready for jobs that benefit from steady, mechanical feeding. Select the Maggi Steff 2032 when you want a 3-roll, 4-speed feeder matched to single-phase shop power for repeatable stock handling.
Sold In: 1 Each