
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Maggi Steff 2034 stock feeder 3-roll 4-speed feeder with stand 230V 3-phase is designed to keep material moving at controlled rates, which supports consistent cuts on woodworking machines. The unit uses three rollers, so it holds stock at multiple points along the feed path, helping maintain steady pressure as boards pass under tooling. Four feed speeds of 13, 26, 36, and 72 feet per minute let the operator match feed rate to cut quality needs, from slower passes to higher-throughput runs. A 4-3/4 inch roller diameter and 2-1/4 inch roller width give a broad contact area on the workpiece, which helps reduce slippage on properly prepared stock. The machine configuration with a 3/4 HP motor on single-phase machines or a 1 HP motor on three-phase machines provides power matched to typical woodworking feed demands. The complete setup is supplied with a universal support column, so the feeder can be positioned relative to the machine table for proper material engagement.
The Maggi Steff 2034 3-roll 4-speed feeder is supplied with a universal support column, which provides a mounting structure that can be adjusted relative to the host machine. That column lets the feeder head swing and position so the three rollers can sit where they contact the work surface at the intended point ahead of the cutter. With roller diameters of 4-3/4 inches and a roller width of 2-1/4 inches, the head geometry supports positioning that balances reach and pressure on typical woodworking tables. The available feed speeds of 13, 26, 36, and 72 feet per minute let installers and operators set a rate that aligns with the machine capability, so the feeder pushes material through the cut rather than relying on manual feed effort.
The Steff 2034 3-roll 4-speed feeder with stand 230V 3-phase fits applications where consistent, powered stock movement is needed across a machine table. The three-roller arrangement is well suited to feeding flat material because it contacts the stock at three points, stabilizing boards as they cross the cutter area. A 4-3/4 inch roller diameter gives substantial wrap on the workpiece, so when the feeder is positioned correctly, each roller can carry material smoothly into and out of the cutting zone. The 2-1/4 inch roller width focuses contact in a defined strip, helping maintain firm downward pressure on the material path. With feed speeds of 13, 26, 36, and 72 FPM available, the same feeder can handle slower passes when cut quality is the priority and higher speeds when throughput is the main goal.
The combination of three rollers and four feed speeds gives the Maggi Steff 2034 stock feeder flexibility for different woodworking operations. Multiple rollers hold stock down before, during, and after the cut, which supports straight-line feeding and helps the machine cutter work under more consistent load. The selectable speeds of 13, 26, 36, and 72 feet per minute mean the operator can slow the feed when using larger profiles or speed up for lighter cuts, using the same feeder on a range of setups. Roller geometry with a 4-3/4 inch diameter and 2-1/4 inch width creates a contact patch that helps transmit motor power into the stock, so the rated 3/4 HP motor on single-phase machines or 1 HP motor on three-phase machines can drive normal feed work. The complete unit weight of 153 pounds gives the assembly a substantial presence, which helps the support column and head remain steady once positioned for repeat runs.
The Maggi Steff 2034 stock feeder uses three powered rollers to move material past machine cutters at controlled speeds, supporting consistent feed and reducing reliance on manual pushing during operations.
The Steff 2034 3-roll feeder provides four feed speeds of 13, 26, 36, and 72 feet per minute, allowing operators to match material feed rate to the type of cut and finish requirements.
The Steff 2034 feeder has rollers with a 4-3/4 inch diameter and 2-1/4 inch width, giving a broad contact area on the workpiece to help maintain traction during feeding.
The universal support column provides an adjustable mounting structure for the feeder head, so installers can position the rollers over the machine table where they best contact the stock path.
The Maggi Steff 2034 feeder is specified with a 3/4 HP motor on single-phase machines and a 1 HP motor on three-phase machines, supplying power appropriate for stock feeding tasks.
The Maggi Steff 2034 3-roll 4-speed feeder has a weight of 153 pounds, giving the unit a solid presence that supports stable mounting on its universal support column during operation.
The Maggi Steff 2034 3-roll 4-speed feeder with stand 230V 3-phase combines three rollers, four selectable speeds, and a universal support column to deliver controlled stock movement across woodworking machines. Its roller diameter of 4-3/4 inches and 2-1/4 inch width provide a firm contact patch for feeding typical flat material. With the motor configuration of 3/4 HP on single-phase machines and 1 HP on three-phase machines driving speeds of 13, 26, 36, and 72 FPM, the unit supports a range of cut depths and production targets. For shops and installers seeking a feeder that pairs defined roller geometry with adjustable support, this model offers a structured way to bring powered feed into regular machine setups.
Sold In: 1 Each