Replacement Filter Bag for Dc-1200 from JET Tools is a dust collector filter bag designed for JET DC-1100VX, DC-1200VX, and DC-1200 30 Micron units, so one part number can service multiple common collectors in the shop. The JET FB-1200 replacement filter bag is rated for 1,200 CFM air flow at 4 feet, which supports dust collection on machines sized for that airflow without choking the system. An efficiency rating of 2 micron means the bag captures fine dust down to that level, helping keep airborne dust lower around the collector connection points. The bag uses a 20 inch diameter, which matches the specified dust collectors and allows the bag to seat correctly on the housing. A 29 inch collection bag length with a 5-3/10 cubic foot capacity gives room for chips and dust to accumulate between changeouts.
This JET Tools replacement filter bag is specified to fit the JET DC-1100VX, DC-1200VX, and DC-1200 30 Micron dust collectors, so installers match the 20 inch diameter to the collector ring without adapting the housing. The 29 inch length and 5-3/10 cubic foot capacity give a defined hanging depth, which helps position the bag so dust settles at the bottom while airflow continues across the filter area. The 1,200 CFM at 4 feet rating aligns with the airflow of these dust collectors, which supports performance when the bag is properly secured on the machine. The 2 micron efficiency rating means the fabric is built to filter down to that level, influencing how the bag behaves in normal cabinet shop dust environments.
The JET FB-1200 replacement filter bag is used on JET DC-1100VX, DC-1200VX, and DC-1200 30 Micron dust collectors, so it serves machines commonly found in cabinet and woodworking shops. The 20 inch bag diameter and 29 inch bag length define how the bag hangs from the collector ring, which affects how dust and chips settle inside during operation. With 5-3/10 cubic feet of collection capacity, the bag holds a known volume of waste before servicing, which supports planning around runs that generate a lot of chips, such as planing or jointing. The 1,200 CFM air flow rating at 4 feet ties directly to collectors sized for that airflow, which matters when the dust collector is connected to tools expecting that draw along the duct run.
The 2 micron efficiency rating on this JET Tools filter bag means the fabric is designed to capture dust down to that size, which directly affects how much fine material stays in the collection stream versus escaping around the collector. When installed on a JET DC-1100VX, DC-1200VX, or DC-1200 30 Micron unit, the 20 inch diameter lets the bag seal on the housing, which supports maintaining suction and keeping the rated 1,200 CFM air flow at 4 feet. The 29 inch length creates a vertical drop where heavier chips and dust settle toward the bottom of the 5-3/10 cubic foot collection volume, which helps keep the upper area open for airflow. Using the JT9-708698 part number or the FB-111212A (FB-1200)/DC-1100A label identifies this exact configuration, which matters when consistent dust collection performance is important from one replacement to the next.
Replacement Filter Bag for Dc-1200 fits JET DC-1100VX, DC-1200VX, and DC-1200 30 Micron units, so it is used specifically on those JET dust collectors in dust collection setups.
The 1,200 CFM at 4 feet rating indicates this filter bag is sized for dust collectors operating at that airflow, which supports maintaining collection performance at typical connection points.
The 2 micron efficiency means the bag captures dust particles down to that size, which helps keep more fine dust in the dust collection system instead of returning to the shop air.
The filter bag has a 20 inch diameter and 29 inch length, which sets how it fits the collector ring and how much vertical space it uses beneath the dust collector.
The JET filter bag has a 5-3/10 cubic foot collection capacity, which defines how much dust and chips it holds between service intervals on the connected machines.
The JT9-708698 number and FB-111212A (FB-1200)/DC-1100A label identify this specific JET Tools filter bag model, which helps match replacements to the same dust collector setup.
The JET Tools Replacement Filter Bag for Dc-1200 combines a 20 inch diameter, 29 inch length, and 5-3/10 cubic foot capacity with a 2 micron efficiency rating, so it matches the stated JET dust collectors and supports their 1,200 CFM performance. Using the JT9-708698 and FB-111212A references connects this filter bag directly to the DC-1100VX, DC-1200VX, and DC-1200 30 Micron units for straightforward replacement on existing dust collection systems.