Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
25 inch 100 grit aluminum oxide sandpaper gives a consistent, medium-fine cut that levels stock on the drum while leaving a surface ready for further sanding steps. The aluminum oxide abrasive works steadily along the drum, so each pass removes material in a predictable way that supports controlled thicknessing. This JET Tools Ready-To-Wrap abrasive is built for use on the 2550 Drum Sander, so the wrap length and grit are matched to that machine for straightforward fitting. The JT9-60-25100 part number identifies this specific 25 inch, 100 grit setup, helping keep repeat orders and changeouts organized in the shop. With this configuration matched to the 2550 Drum Sander, the abrasive wraps follow the drum path properly, which supports even contact across the board width and consistent performance on repeat runs.
JET Tools Ready-To-Wrap abrasives for the 2550 Drum Sander are sized so the 25 inch wrap follows the drum path as intended, supporting even tracking across the full sanding width. The 100 grit aluminum oxide cut means each wrap delivers the same sanding character, so changing wraps maintains a known surface profile from job to job. With three wraps in each set, the same JT9-60-25100 configuration can stay on the machine across multiple runs, which keeps sanding behavior predictable over time. Using a wrap format matched to the 2550 Drum Sander reduces time spent trimming or adjusting abrasive lengths and keeps attention on feeding stock through the machine.
JET Tools designates these Ready-To-Wrap abrasives for the 2550 Drum Sander, so they are intended to run directly on that machine for routine drum sanding tasks. The 25 inch length is configured around the drum on the 2550, which lets the abrasive track along the drum without overhanging or falling short, supporting dependable contact with the work. Because it is a 100 grit aluminum oxide abrasive, the wrap is suited to stages where boards are already close to final size and need leveling and refining rather than heavy stock removal. Matching the JT9-60-25100 part to the 2550 Drum Sander keeps abrasive selection straightforward in shops that rely on that specific machine.
The JT9-60-25100 Ready-To-Wrap format ties the 25 inch length, 100 grit, and aluminum oxide abrasive together as one defined setup, which helps keep surface results consistent from one wrap change to the next. Aluminum oxide in 100 grit gives a controlled, medium-fine cut, so when a wrap is changed to another from the same 3-Pack, the drum keeps producing a similar finish without changing sanding passes. The Ready-To-Wrap abrasives for the 2550 Drum Sander are pre-sized for that drum, so each wrap follows the same spiral path and tension, supporting even wear across the abrasive and consistent sanding over the working width. With three wraps grouped in a single 3-Pack, shops can plan several abrasive changes using the same configuration, which supports steady workflow when running multiple batches that call for the same finish level.
These Ready-To-Wrap abrasives are for the 2550 Drum Sander, so the 25 inch wrap length and format are matched to that specific JET Tools machine.
The 25 inch length is configured for the drum on the 2550 Drum Sander, so the wrap follows the drum path properly and supports even tracking during sanding.
The 100 grit aluminum oxide abrasive gives a medium-fine cut, which helps level stock on the drum while leaving a surface ready for finer grit sanding steps.
The Ready-To-Wrap format is set up for the 2550 Drum Sander, so the abrasive is pre-sized for that drum and supports straightforward wrapping and alignment.
The JT9-60-25100 part number identifies this 25 inch, 100 grit Ready-To-Wrap abrasive, helping shops reorder the same sanding setup for consistent results.
The 3-Pack provides three wraps with the same 25 inch, 100 grit configuration, so multiple drum changes can use the same abrasive setup for predictable sanding behavior.
Choosing the JET Tools JT9-60-25100 Ready-To-Wrap abrasives aligns a 25 inch, 100 grit aluminum oxide wrap with the 2550 Drum Sander for medium-fine sanding stages. With three wraps in each 3-Pack, the same drum-ready configuration can support several runs that call for a matched surface profile. For shops running a 2550 Drum Sander, this setup provides a defined abrasive choice that keeps wrap sizing, grit selection, and reordering tied to one consistent part number.