Cabinet Door Mounting Jig is a Kreg Tool jig designed to give you an extra helping hand when installing cabinet doors, so you can handle doors and fasteners without fighting alignment. The jig works for both face-frame and frameless cabinets, which lets you use the same setup across different cabinet constructions in a shop or on site. It handles both left-hand and right-hand doors, so you can move from one door to the next without rethinking your approach. A built-in support arm holds the door while you mount the hinges to the cabinet, which keeps the door steady and lets your free hand focus on driving fasteners accurately. This setup control helps reduce door shifting during installation, so gaps and reveals stay closer to what you planned.
The Kreg Cabinet Door Mounting Jig is built around a support arm that carries the weight of the door during installation, so you can align hinge positions without the door sagging. When you set the arm to one of its nine positions, you pre-establish where the door will sit relative to the cabinet face, which simplifies hitting a target overlay or inset. The single inset setting gives you a go-to position for doors that sit inside the frame, and the eight 1/4 inch steps up to 2 inches of overlay cover typical overlay layouts. During mounting, the two shims allow small vertical adjustments of 1/16 inch, 1/8 inch, or 3/16 inch, so you can shift the door slightly to clean up a joint or even up a pair of doors after checking their relationship.
This Kreg Tools cabinet door mounting jig works on both face-frame and frameless cabinets, so one tool handles different construction styles in the same project. On a face-frame cabinet, the support arm position sets how far the door overlaps or sits within the frame opening, which ties your hinge mounting to a consistent visual line around the frame. On frameless cabinets, the same nine positions reference from the cabinet side, so overlay up to 2 inches remains predictable along a full bank of doors. Because the jig supports left-hand and right-hand doors, you can move from one side of a cabinet to the other while holding the same dimensional settings for a symmetrical layout.
The nine-position support arm on the Cabinet Door Mounting Jig establishes a coarse setting for inset or overlay, and the two micro-adjustment shims supply the fine control that finishes the fit. Using a single shim shifts the door 1/16 inch or 1/8 inch, while stacking both gives 3/16 inch of total adjustability, which is useful when you want to tighten a reveal without remounting hinges. This combination of fixed arm steps and shim adjustments lets you dial in doors so gaps between pairs, or between door and drawer faces, stay more uniform across a run. Because the jig holds the door while hinges are attached, these adjustments directly influence the mounted position, supporting repeatable results from door to door.
The Cabinet Door Mounting Jig uses a built-in support arm to hold the door while you mount hinges to the cabinet, which keeps the door steady so hinge alignment is easier to control.
The Cabinet Door Mounting Jig is designed for both face-frame and frameless cabinets, so the same jig can be used across different cabinet box constructions in one project or shop.
The jig provides one inset setting and eight positions at 1/4 inch increments, supporting door overlays up to 2 inches so common overlay layouts can be repeated along a cabinet run.
The Cabinet Door Mounting Jig shims give 1/16 inch or 1/8 inch of movement individually, or 3/16 inch when combined, allowing small vertical changes that refine door reveals after the main setting.
The Cabinet Door Mounting Jig works with both left-hand and right-hand doors, so a single setup can be used from one side of the cabinet to the other for mirrored layouts.
The Kreg Tool Cabinet Door Mounting Jig uses manufacturer part number KHI-CDIJ, which identifies this specific door installation jig when matching specs or reordering for additional setups.
The Kreg Tool Cabinet Door Mounting Jig, part number KHI-CDIJ, is built to hold doors while you mount hinges on face-frame and frameless cabinets, so alignment depends more on your layout marks than on hand strength. With a support arm offering one inset position and eight 1/4 inch steps up to 2 inches of overlay, along with shims offering 1/16 inch, 1/8 inch, or 3/16 inch adjustment, this jig gives repeatable control over door placement. Choose this cabinet door mounting tool when you want a dedicated setup that supports both left-hand and right-hand doors and keeps reveals more consistent across your cabinet work.
Sold In: 1 Each