Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
90 degree pocket hole driver from Kreg Tool turns a standard drill into a 90 degree driver, so you can drive screws in places a straight drill body cannot reach on cabinetry or woodworking builds. This compact drill attachment is designed to allow screw driving in tight locations by changing the angle of drive, which helps when working inside cases or close to adjacent panels. It is impact-rated for use with an impact driver, so it can be used in higher-torque fastening setups common in shop and on-site work. The driver works with all hex shank bits, so it serves pocket-hole screw driving and other general screw driving tasks without changing tools. An ergonomic design allows you to hold the attachment in place with one hand while running the drill with the other, improving control in awkward positions. Manufacturer part number KDRV-90DG identifies this specific Kreg 90 degree pocket-hole driver.
This Kreg 90 degree pocket-hole driver works with all hex shank bits, so existing hex-based screw-driving bits can be used directly in the attachment for pocket-hole screws and other screws. The 3 inch square-drive bit that chucks securely into the attachment has a magnetic tip that locks into the head of a pocket-hole screw, giving positive engagement so the screw stays on the bit while you position it in tight spots. Being impact-rated, the attachment handles the percussive action of an impact driver, which matters for driving screws fully in pocket holes or dense stock without sacrificing the right-angle reach. Its ergonomic shape is designed for one-handed holding while the drill is controlled with the other hand, improving stability when fitting the driver into confined casework.
The Kreg 90 degree pocket-hole driver is designed for driving pocket-hole screws and other screws in tight spaces, so it is especially useful inside cabinets, fixtures, or furniture frames where vertical and horizontal clearances are limited. By turning any drill into a 90 degree driver, it lets the chuck and bit approach the screw head from the side, so the drill body can stay outside narrow compartments while the bit extends into the work zone. The compact drill attachment format makes it easier to work near interior corners, along face frames, or behind rails, where a straight drill setup would contact adjacent parts. Because the tool is impact-rated, it can also be put into service on impact drivers in shop or field environments that already rely on impact tools for joining pocket-hole assemblies.
The driver works with all hex shank bits, so you can standardize on hex-based drivers and still use the same 90 degree pocket-hole driver attachment for a wide range of screw types without changing the angle solution. The 3 inch square-drive magnetic-tip bit locks into the pocket-hole screw head and holds it on the bit, which keeps the screw aligned while you guide it through a pocket into the mating piece. This secure hold matters when driving at odd angles, because the screw remains seated on the bit as you reach into deep cabinets or under fixed tops. The ergonomic, easy-grip design lets one hand clamp the attachment at the correct angle while the other hand feathers trigger and speed, which supports consistent pocket-hole screw seating and reduces wandering off the pilot path. With the attachment being impact-rated, you can maintain this controlled, angled approach even when extra torque is required, helping pocket-hole joints draw tight without changing tools or setups.
The Kreg 90 degree pocket-hole driver is used to drive screws in tight spaces by turning a standard drill or impact driver into a 90 degree driver for pocket-hole and other screw joints.
The Kreg 90 degree pocket-hole driver is impact-rated for use with an impact driver, which lets you apply higher torque at a right angle when driving screws in dense materials.
The Kreg 90 degree pocket-hole driver works with all hex shank bits, so hex-based drivers for different screw heads can be used in the same right-angle attachment.
The 3 inch square-drive magnetic-tip bit locks into the head of a pocket-hole screw, so the screw stays seated on the bit while you position and drive it in confined areas.
The ergonomic, easy-grip design lets one hand steady the 90 degree pocket-hole driver while the other runs the drill, improving control when driving screws in awkward orientations.
Manufacturer part number KDRV-90DG identifies this specific Kreg 90 degree pocket-hole driver model, which helps match the right-angle drill attachment needed for pocket-hole screw driving.
The Kreg 90 degree pocket-hole driver KDRV-90DG offers a compact, impact-rated right-angle drill attachment that works with all hex shank bits, so pocket-hole screws and other fasteners can be driven where straight drills cannot reach. Its 3 inch square-drive magnetic-tip bit locks into pocket-hole screw heads, adding stability as you reach into cabinets or frames. The ergonomic, easy-grip design supports steady one-handed holding while operating the drill, helping deliver consistent screw seating in confined or awkward spaces. For cabinet, furniture, or built-in projects that demand screw driving in tight areas, this 90 degree pocket hole driver provides a straightforward way to turn existing drills or impact drivers into right-angle tools.
Sold In: 1 Each